background image

AM252171_02_V.pdf

October 22, 2001

9

Cleaning your speakers

Clean the cabinets of your Acoustimass

®

 3 system using a damp cloth. If necessary, use a

mild detergent such as dish soap. Do not use any solvents, chemicals, or cleaning solutions
containing alcohol, ammonia, or abrasives. Do not allow liquids to spill through the speaker
grilles or enter the Acoustimass module.

You can vacuum the speaker grilles. To avoid damaging the drivers located directly behind
the grille cloth, use light pressure only.

Troubleshooting

If you have a problem with your Acoustimass 3 speaker system, turn off the amplifier or
receiver and check all the connections between the cube speakers, the module, and amplifier
or receiver. Since problems are likely to originate with components other than speakers, you
may want to refer to your amplifier or receiver owner’s guide.

Problem

What to do

The left cube speaker does

• Disconnect both speaker cables from the amplifier or receiver. Reconnect the cable from

not play or sounds distorted.

the bass module’s L INPUTS to the amplifier or receiver’s RIGHT speaker terminals.
Set the amplifier or receiver’s balance control all the way to the right and turn on the power.

• If the left cube speaker now plays properly, your amplifier or receiver’s left speaker channel

is probably defective.

CAUTION:

 DO NOT connect the other cube speaker to the channel in question. If the

channel is defective, it could damage your Acoustimass 3 system.

The right cube speaker does

• Follow the above steps, reconnecting the cable from the module’s R INPUTS to the

not play or sounds distorted.

amplifier or receiver’s LEFT speaker terminals.

The entire Acoustimass 3

• Disconnect the amplifier or receiver from the bass module. Reconnect the module to

system does not play or

another amplifier or receiver that is working properly.

sounds distorted.

• If the system now works, the problem is in your amplifier or receiver. Refer to your receiver

or amplifier owner’s guide for further suggestions.

• If trouble persists in your Acoustimass 3 speaker system, contact your authorized Bose

®

dealer who will verify any defects and arrange for service by an authorized agency or by the
Bose factory. Bose will make every effort to remedy any problem within the terms of the
warranty at minimum inconvenience to you.

Maintaining Your Acoustimass

®

 Speaker System

Summary of Contents for Acoustimass 3 Series


















Reviews: