background image

 

9

DR-3

 

fig.volume

 

3.

 

Use an oscilloscope to observe the waveforms from OUTPUT L/R (PIN 
jack) on the DR-3.

 

fig.lineout-1

 

• Waveforms like those shown above must be output from LINE OUT L/

R.

• They must be rectangular waves phase-shifted by 90 degrees.

• The waveform height must be from 1.8 V to 2.4 V.

4.

Observe the waveform from the tip of R (MONO) on the DR-3.

Nothing must be plugged into L (PHONE) at this time.

fig.lineout-2

• A stepped waveform like the one shown above must be output from R 

(MONO).

5.

Observe the waveforms from the tip of L (PHONE) and from the tip of R 
(MONO) on the DR-3.

fig.lineout-3

• They must be rectangular waves phase-shifted by 90 degrees, like those 

shown above.

• The waveform height must be from 1.8 V to 2.4 V.

6.

Disconnect the plug from R (MONO).

Insert a stereo plug into L (PHONE) and waveforms of the tip and the 
ring.

fig.lineout-4

7.

Turn [VOLUME] on the DR-3 to “MAX,” then to “MIN,” then back to 
“MAX,” and make sure the waveforms change smoothly.

Also, make sure that the waveforms disappear completely when 
[VOLUME] is set to “MIN.”

fig.volume

8.

Press the [EXIT] button to end the SQUARE Check.

13.SINE Check

This item is used only during the shipping test at the factory.

You need not use it when servicing in the field.

14.MUTE Check

This item is used only during the shipping test at the factory.

You need not use it when servicing in the field.

15.Ending the Test Mode

Switch off the DR-3.

16.Checks for Normal Operation

1.

Switch on the DR-3 unit.

2.

Connect headphones to L (PHONES) on the DR-3.

fig.phone

Lch

1V/DIV

0.2s/DIV

LINE OUT

Rch

VOLTS 1V/DIV, TIMES 0.2S/DIV

Lch

1V/DIV

0.2s/DIV

L(PHONE) / R(MONO)

Rch

VOLTS 1V/DIV, TIMES 0.2S/DIV

Lch

1V/DIV

0.2s/DIV

L(PHONE) / R(MONO)

Rch

VOLTS 1V/DIV, TIMES 0.2S/DIV

RING

1V/DIV

0.2s/DIV

L(PHONE) TIP / RING

TIP

VOLTS 1V/DIV, TIMES 0.2S/DIV

Headphone

Summary of Contents for Dr. Rhythm DR-3













Reviews: