background image

11

LED check

Green

Improve the

feeder

system

Strong interference near donor

antenna

Abnormal

Feeder system

inspection

Improve the

power supply

system

Red

Off

Isolation

inspection

Power supply

inspection

Abnormal performance

Abnormal

Abnormal

Abnormal

Chapter 6 Product Maintenance

6.1 Operation and maintenance

Power supply

Please make sure the voltage and frequency comply with the repeater requirement.

Component replacement

Please do not maintain or replace components by yourself, otherwise may get an

electric shock. Only the authorized professional can maintain and replace the
components.

Waterproof and moist proof

Please do not turn on or off the booster in moist environment when its door is

opened.

6.2 Emergency dealing

Switch off is recommended during following situations:

The power supply is not normal

Liquid flows into the equipment;

Working conditions is not normal, (overheating, abnormal smelling, abnormal sundries)

Closet damage

performance debasement

near to fire

flooding

6.3 Maintaining direction

Please check the repeater step by step according to below process, to find out the problem

with the repeater.

Contact supplier

Summary of Contents for BOSSGSM-LED-HP27D












Reviews: