-4-
TOOL SPECIFICATIONS
MODEL LENGTH
HEIGHT WIDTH WEIGHT
TU-216-71
8.71" (221.25 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
1.88 lb (.853 kg)
TU-216-71LN
8.71" (221.25 mm)
7.81” (198.30 mm)
1.58” (40.2 mm)
2.01 lb (.912 kg)
TU-216-71LM
13.925” (353.69 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
2.34 lb (1.061 kg)
TU-216-71A
8.71” (221.25 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
1.91 lb (.867 kg)
TU-216-71ALM
13.925” (353.69 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
2.37 lb (1.075 kg)
TU-216-80
8.71” (221.25 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
1.82 lb (.807 kg)
TU-216-80LN
8.71" (221.25 mm)
7.81” (198.30 mm)
1.58” (40.2 mm)
1.97 lb (.894 kg)
TU-216-80LM
13.925” (353.69 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
2.23 lb (1.012 kg)
TU-216-80ALM
13.925” (353.69 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
2.26 lb (1.025 kg)
TU-216-84
8.71” (221.25 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
1.82 lb (.826 kg)
TU-216-97
8.71” (221.25 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
1.79 lb (.813 kg)
TU-216-SJK
8.71” (221.25 mm)
5.92” (150.26 mm)
1.58” (40.2 mm)
1.79 lb (.813 kg)
TOOL MODEL
STAPLE SERIES
CROWN WIDTH
WIRE SIZE
FASTENER RANGE
TU-216-71
BA71
3/8” (9.0 mm)
.023X.030(.58mmX.75mm)
5/32"-5/8"(4mm-16mm)
TU-216-71LN
BA71
3/8” (9.0 mm)
.023X.030(.58mmX.75mm)
5/32"-5/8"(4mm-16mm)
TU-216-71LM
BA71
3/8” (9.0 mm)
.023X.030(.58mmX.75mm)
5/32"-5/8"(4mm-16mm)
TU-216-71A
BA71
3/8” (9.0 mm)
.023X.030(.58mmX.75mm)
5/32"-5/8"(4mm-16mm)
TU-216-71ALM
BA71
3/8” (9.0 mm)
.023X.030(.58mmX.75mm)
5/32"-5/8"(4mm-16mm)
TU-216-80
BA80
1/2” (13mm)
.027X.036(.69mmX.91mm)
5/32”-5/8”(4mm-16mm)
TU-216-80LN
BA80
1/2” (13mm)
.027X.036(.69mmX.91mm)
5/32”-5/8”(4mm-16mm)
TU-216-80LM
BA80
1/2” (13mm)
.027X.036(.69mmX.91mm)
5/32”-5/8”(4mm-16mm)
TU-216-80ALM
BA80
1/2” (13mm)
.027X.036(.69mmX.91mm)
5/32”-5/8”(4mm-16mm)
TU-216-84
SBNK, ATRO 84
31/64”(12.3mm)
.023X.040(.55mmX1mm)
5/32”-5/8”(4mm-16mm)
TU-216-97
BA97
3/16”(4.8mm)
.027X.036(.69mmX.91mm)
5/32’-5/8”(4mm-16mm)
TU-216-SJK
ATRO SJK
5/32”(4.1mm)
.024X.029(.60mmX.70mm)
5/32”-5/8”(4mm-16mm)
All screws and nuts are metric
FASTENER SPECIFICATIONS
TOOL AIR FITTING
This tool uses a free-flow connector plug, 1/4 N.P.T. The inside diameter should be .200”
(5mm) or larger. The fitting must be capable of discharging tool air pressure when
disconnected from the air supply.
OPERATING PRESSURE
70 to 100 p.s.i.g. (4.8 to 6.9 bar). Select the operating pressure within this range for best
fastener performance.
DO NOT EXCEED THE RECOMMENDED OPERATING PRESSURE.
AIR CONSUMPTION
The TU-216 requires 1.71 cubic feet per minute (.048 cubic meters) and the TU-216-LN
models require 1.84 cubic feet per minute (.052 cubic meters) of free air to operate at the
rate of 100 nails per minute, at 80 p.s.i. (5.5 bar). Take the actual rate at which the tool
will be run to determine the amount of air required. For instance, if your fastener usage
averages 50 nails per minute, you need 50% of the tool’s c.f.m. which is required to
operate the tool at 100 nails per minute.
