background image

Specifications

Micro90c

Micro90x

Micro80x

Frequency Response (±3dB)

100 –20,000Hz

120–20,000Hz

120 –20,000Hz

Recommended Amplifier Power

15 –125 watts

15 –125 watts

15 –100 watts

Nominal Impedance

8 ohms

8 ohms

8 ohms

Sensitivity [1 watt (2.83v) at 1m]

90dB

89dB

89dB

Tweeter

1" (25mm) 

1" (25mm) 

3

4

" (19mm) 

aluminum dome

aluminum dome

dome

Bass Unit

(dual) 3

1

2

" (89mm)  

3

1

2

" (89mm)  

3

1

2

" (89mm) 

copolymer

copolymer

copolymer 

Crossover Frequency

2500Hz

3800Hz

4500Hz

Dimensions (HxWxD)

4

3

4

x 12 x 5

1

4

" 6

7

8

x 4

1

4

x 5

3

4

"

6

7

8

x 4

1

4

x 5

3

4

(120 x 300 x 132mm)

(175 x 108 x 146mm)

(175 x 108 x 146mm)

Weight

11 lbs (5kg)

6 lbs ea. (3kg)

4 lbs ea. (2kg)

Finish

Black 

Black or white

Black or white

Description

Micro90c Center Channel Speaker System

The Micro90c center channel speaker system delivers exceptionally articulate on-screen dialog

and effects from a small, sleek package. Point-source driver spacing and a low crossover fre-

quency assure wide, uniform horizontal dispersion for complete coverage of the listening area. 

MagnaGuard

®

magnetic shielding ensures the speaker’s magnetic field does not interfere with

the television’s picture.

Micro90x and 80x Satellites

Micro Reference satellites are ideally suited for use as surround speakers in a high-quality home

theater system, or as extension speakers for another room in the house. The included wall-

mount brackets make installation easy, and MagnaGuard

®

magnetic shielding allows placement

next to a television or computer monitor.

Summary of Contents for Micro80x II
















Reviews: