background image

www.bostongear.com

701 Carrier Drive

Charlotte, NC 28216

704-588-5610

Warranty

Boston Gear warrants that products manufactured or sold by it shall be free from defects in material and 
workmanship. Any products which shall within two (2) years of delivery, be proved to the Company’s satisfaction 
to have been defective at the time of delivery in these respects will be replaced or repaired by the Company at its 
option. Freight is the responsibility of the customer. The Company’s liability under this limited warranty is limited 
to such replacement or repair and it shall not be held liable in any form of action for direct or consequential 
damages to property or person. THE FOREGOING LIMITED WARRANTY IS EXPRESSLY MADE IN LIEU OF 
ALL OTHER WARRANTIES WHATSOEVER, EXPRESS, IMPLIED AND STATUTORY AND INCLUDING WITHOUT 
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS.

No employee, agent, distributor, or other person is authorized to give additional warranties on behalf of Boston 
Gear, nor to assume for Boston Gear any other liability in connection with any of its products, except an officer of 
Boston Gear by a signed writing.

P-3003-BG     9/18

Summary of Contents for ORC-S Series





















Reviews: