5-6
Section 5 • Care & Maintenance
R
190 Montauk
•
Seemingly permanent stains
like ballpoint ink
can be cleaned with active solvents such as
nail polish remover when applied with a soft
cloth or damp sponge and rubbed. Rinse
cleaned area with fresh water and dry
with a clean, soft, lint-free cloth or towel.
The vinyl material and superior finish has been
tested to resist heavy abrasion. Complete cleaning
instructions are included in the owner’s packet. Read
all information provided by the cushion manufacturer
regarding the proper cleaning and maintenance.
Your cushions are not waterproof.
They are
constructed of open-cell foam and will absorb and
hold water.
Do not leave the cushions in standing
water or exposed to heavy, prolonged rain
.
If, in the event your cushions become waterlogged,
remove the foam from the cushion, press as much
water as you can from the foam and allow to air dry.
To prevent mildew, keep the vinyl dry and make
sure that moisture does not accumulate between the
cushions.
Cleaning Your Instrument Gauges
When gauges are exposed to a saltwater environment,
salt crystals may form on the bezel and plastic covers.
Remove the salt crystals with a soft damp cloth.
Clean with a mild household detergent or plastic
cleaner.
Never use abrasives or rough, dirty cloths to clean
plastic parts. A mild household detergent or plastic
cleaner should be used. Wipe clean with a damp
chamois.
FOR MORE INFORMATION, CONTACT MERCURY MARINE
CUSTOMER SERVICE AT 1-920-929-5040
If equipped, the T-top frame and/or tow arch on your
boat has been manufactured with a powder coating.
While most powder coat finishes are tougher and
much more flexible than conventional solvent
based paints, they are about the same hardness as
automotive paint, so they will scratch.
To clean a powder coated surface, gently wash with
a clean, soft cloth and a mild detergent followed by
a clear water rinse.
Even though most powder coatings are highly
resistant, certain solvents can harm them and should
be avoided.
DO NOT APPLY:
• Nail polish remover
• Paint or lacquer thinner
• Motor oils
• Transmission or brake fluids
• Parts cleaning fluids
If any of the above should contact the powder coated
surface, immediately wipe the area with a soft, clean
cloth, and wash as described above.
Powder Coated Surfaces
If it is necessary to apply touch-up paint on areas
of the finish that have been scratched or damaged
the powder material supplier should be contacted
for their recommendation of the proper touch-up
material to use.
Single component Acrylic Enamel (spray enamel)
touch-up paint is commonly used for repair of minor
damage in the powder coated finish. In some cases
a two-component catalyzed paint system may be
required to achieve the desired repair. In all cases,
perform a color and adhesion test in an inconspicuous
area of the finish to assure compatibility before
applying the paint to the damaged area.
Powder Coating Touch-Up
NOTICE
For the best results, use Orbit Industries
touch-up paint, RAL 9010 Pure White.
Orbit Industries: 1-800-448-3885
Summary of Contents for 190 Montauk
