background image

Page 38

37355-0-0217

TO TURN OFF GAS TO FIREPLACE

1.  STOP! Read the safety information above.

2.  Turn OFF electric power to the appliance.

3.  Turn gas shutoff valve counterclockwise 

 to 

 

On position.

4.  Wait ten (10) minutes to clear out any gas. Then smell for 

gas, including near the floor. If you smell gas, STOP! Follow 

B in the safety information above on this page. If you do not 

smell gas, go to the next step.

5.  Turn ON electric power to the appliance.

6.  Find pilot. The pilot is next to the burner.

7.  Turn main flame to on. If the pilot does not light within 60 

seconds, stop and go to Step 5.

8.  Refer to remote control instructions for detailed information, 

control features, and operation. 

NOTICE:

 There is a CPI/

IPI switch for a continuous standing pilot mode or an 

intermittent pilot mode. See appliance manual for location 

of this switch. If the pilot or burner does not stay lit (in the 

standing pilot mode), stop and immediately call a qualified 

service technician or gas supplier.

9.  If the burner or pilot does not operate properly after several 

tries, turn the gas valve clockwise 

 to OFF and call 

your service technician or gas supplier.

10.  Operation of the gas valve is controlled by a manual on/

off switch or a hand held remote control. Refer to remote 

instructions for detailed operation information.

FOR YOUR SAFETY READ BEFORE LIGHTING

A.  

This appliance has a pilot which can be lit by hand or by 

switching the remote receiver switch to the "ON" position. 

When lighting the pilot, follow these instructions exactly.

B.  Before lighting smell all around the appliance area for gas. 

Be sure to smell next to the floor because some gas is 

heavier than air and will settle on the floor.

  What To Do If You Smell Gas

•  Do not try to light any appliance.

•  Do not touch any electrical switch; 

•  Do not use any phone in your building.

•  Immediately call your gas supplier from a neighbor's 

phone. Follow the gas supplier's instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

C.  If applicable, use only your hand to turn the gas shutoff valve 

handle. Never use tools. If the handle will not turn by hand, 

don't try to repair it; call a qualified service technician. Force 

or attempted repair may result in a fire or explosion.

D.  Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect the 

appliance and to replace any part of the control system and 

any gas control which has been under water.

LIGHTING INSTRUCTIONS

LIGHTING INSTRUCTIONS

GAS SHUTOFF VALVE

WARNING

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, 

personal injury or loss of life.

1.   Set REMOTE/OFF/ON switch to OFF.

2.   Turn off all electric power to the appliance if service is to be 

performed (if applicable).

3.   Turn gas shutoff clockwise 

 to OFF. Do not force.

Summary of Contents for VFLL60SP90LN-1

















































Reviews: