background image

8

Adjusting Length

Loosen the locking collar nut 1/4 turn

Extend the bottom tube assembly

1.

Grasp the top tube with one hand.

2.

Grasp the searchcoil with the other hand.

3.

Pull the two sections apart to slide the lower stem out of the upper
stem.

**

Try not to pull lower tube all the way out.

Establish Tube Length

1.

Pivot the searchcoil perpendicular to the tube.

2.

Place detector in user’s hand,
with arm extended.

3.

Adjust stem length so that searchcoil
rests on the ground, close to
the user’s feet.

4.

Align the searchcoil so it is
parallel to the ground.

5.

Tighten the locking collar
while holding the
searchcoil in place on
the ground to prevent
twisting of the stem
assembly while
tightening.

Do not over-tighten.

6.

Leave approximately
2” of the lower
stem inside the
upper stem to help
maintain rigidity.

9

Target Identification and Discrimination

The  Bounty  Hunter  Mach1  metal  detector  can  both  identify  buried  metals  by
category, and eliminate unwanted metals from detection.
“Discrimination”  refers  to  the  detector’s  ability  to  both  identify  targets  and
eliminate them from detection.  When a Target ID category has been eliminated
from detection, we say it has been “discriminated out.”

Target Identification

The Mach1 can distinguish between four categories of metal targets:

1. Ferrous:

This includes many

iron  targets  such  as  nails,
screws, bolts and some large
iron objects like horseshoes.
The Mach1 will respond with
a  bass  audio  tone  and
display the

icon.

2. Non-ferrous  low  conductor:

This  includes  many  small
rings  and  small  jewelry  but
also  includes  many  trash
items such as foil and newer
pull-tabs.  The  Mach1  will
respond  with  a  low-pitch
audio  tone  and  display
the

icon.

3. Non-ferrous medium

conductor:

This    category

includes  U.S.  nickels,  larger
rings  and  large  jewelry  but
also  includes  many  trash
items such as older pull-tabs.
The Mach1 will respond with
a  medium-pitch  audio  tone
and display the

icon.

4. Non-ferrous  high  conductor:

This  includes  most  copper
and  silver  coins,  as  well  as
modern  clad  coins.  The
Mach1  will  respond  with  a
high-pitch  audio  tone  and
display the

icon. 

Probably Trash

Trash or small valuables

Could be something good?

Usually high value

Summary of Contents for Mach-1

















Reviews: