background image

Table 5: Electrical Data 

The electrical characteristics are within ±10 percent of the indicated values of Isc, Voc and Pmax under Standard Test 
Conditions (STC) (irradiance of 100mW/cm², AM 1.5 spectrum, and a cell temperature of 25° (77°F)).

Under normal conditions, a photovoltaic module is likely to experience conditions that produce more current and/or 
voltage than reported at standard test conditions. The requirements of the National Electrical Code (NEC) in Article 690 
shall be followed to address these increased outputs. In installations not under the requirements of the NEC, the values 
of Isc and Voc marked on this module should be multiplied by a factor of 1.25 when determining component voltage 
ratings, conductor ampacities, overcurrent device ratings, and size of controls connected to the PV output.

No

Technical Highlight

Information

1

System voltage (V)

DC1000V/1500V

2

Power Tolerance

0~+5W

3

Insurance Current (A)

15/20

≥ 40MΩ, M

2

4

Insulation resistance

≥ 40MΩ

5

Application Class

Class A

6

Standard Test Conditions

(STC) : AM=1.5, E=1000W/m

2

,

 

T=25°C

07 

|

 

WIRING AND NOTES

All wiring should be performed by qualified installers according to the local codes and regulations.

1.   Before connecting modules, always ensure that the contacts are corrosion free, clean, and dry.

2.   Before connecting modules, verify that the proper electrical values are measured.

3.   To minimize the risk of indirect lighting strike and avoid forming closed loops, review that wiring has been properly  

done before starting. If the measured data of open circuit voltage and short-circuit current differ from the 
specifications, please check the wiring before proceeding.

4.   Products can be irreparably damaged if an array string is connected in reverse polarity to another. Always verify the 

voltage and polarity of each individual string before making a parallel connection. If strings are connected in reverse 
polarity and a difference of more than 2V between 10 strings are measured, please check the string wiring  
before making the parallel connection. 

13

Summary of Contents for Vega BVM6610M S-H-HC-BFDG Series


















Reviews: