background image

08 

|

 

MAINTENANCE INFORMATION

A well-designed system needs minimal maintenance.

Maintenance should be carried out at least once a year by well-trained personnel.

Check that the mounting hardware is properly tightened. Check if cables, nuts, and bolts are secure and not loose. 
Tighten any loose components if necessary.

Check ground resistance performance and water resistance of connecting cables, grounding cables, connectors, and  
any other connections.

Verify that the   electrical and mechanical connections are free from corrosion.

Do not touch the live part of the wire, cable, or connector directly, but only with safety equipment (insulating tools and 
electrical protection) when necessary.

Use an opaque cloth or other opaque materials to cover the front side of the modules during the maintenance. When 
exposed to sunlight the module may produce high voltage which can cause injury and even death.

In the event that modules need to be cleaned, clean modules with a soft cloth together with a mild detergent and clean 
water. To avoid severe thermal shocks, which might damage the module, use water at a similar temperature to the 
modules being cleaned.

09 

|

 

WARNING INFORMATION 

Contact your installer immediately if you suspect your system is not working properly. For any warranty related concerns 

contact our Boviet Solar after sales service team at  service@boviet.com or your sales contact.

WARNING: The PV system must be shut down first if it needs any electrical maintenance. Improper maintenance may 
cause burns and/or electrical shock, which can both be lethal. 

CONTACT

Address:   
Website:

2107 N. 1st Street, Suite: 550, San Jose, CA, USA, 95131
bovietsolar.com

16

Disclaimer: The information included in this document is subject to change without any notice and is provided for informational purposes only. No 
contractual rights are established or should be inferred because of user’s reliance on the information contained in this PV module installation manual 
Please contact with Boviet Solar’s local offices for more up-to-date product information.

Summary of Contents for Vega BVM6610M S-H-HC-BFDG Series


















Reviews: