Service Manual 04/2010 Rev.B
118
Lift and lower by hand the hook to verify that it
has a slight contact with saddle bar:
If the
hook needs to be forced when lifting or
lowering, or if it jumps up and down freely,
it must be adjusted.
Perform the same control on five different
position of the saddle.
TO ADJUST THE HOOK:
Remove the nut #1 (Fig.280).
Fig.280
Push out the screw #2 for at least 7/8mm
(1/4”) (Fig.281)
Fig.281
Remove the eccentric plate #3 and #4
(Fig.280 and 281).
Turns clockwise or counter clockwise one or
both eccentrics ‘till to have the adjustment
above reported (Fig.282).
Fig.282
Install the eccentric plates #3 and #4.
Tighten the nut #1 FIRMLY and the turn it
back ‘till to have the hook free.
Mount the lifting cylinder
6.18.
Mount the rotation proof spring
7.9.
Mount the mount dismount tool..
Check if the machine works fine.
7.12 BOXER KING 5600R HOOK:
CHECK AND REPLACEMENT
:
1h
:
End wrench of 13,22 and 30mm, Allen
wrenches of 4mm, rubber hammer, green
loctite.
L
:
Defective hook may cause the following
malfunctions:
1. Damaging of the tool holder assy.
2. Tool holder lifting cylinder damaging.
3. No eccentrics adjustment.
NOTE: BEFORE STARTING WITH HOOK
ADJUSTMENT VERIFY IF THE TOOL HOLDER
ARM SCREW SUPPORT IS WELL ADJUSTED
7.15.
TO CHECK THE HOOK:
Check the following
7.11.
TO REPLACE THE HOOK:
Replace the hook following
7.11.
NOTE: VERY OFTEN THERE ARE SOME
SHIMS BETWEEN THE HOOK AND ITS
SUPPORT. AFTER REPLACING THE HOOK
INSTALL THESE SHIMS IN THE SAME
POSITION AGIN.
7.13 BOXER KING 5600 HOOK:
CHECK AND ADJUSTMENT
Summary of Contents for KING 5600
