Service Manual 04/2010 Rev.B
125
Clean the gear oil tank and all oil protection
from old silicon very accurately and wash
them by using alcohol.
Clean the worm screw assy screws and
bracket holes from dry loctite.
Mount the worm screw on the crown gear and
insert the shims, if there are.
Tighten the screws #1, #2, #3 and #4 by
hands.
Turn clockwise of a turn the screw #2
(Fig.297).
Take a tyre lever and push up the worm screw
(Fig 299).
Fig.299
Take the wrench and tighten the screws #2,
#3 and #4 (Fig.298),by keeping the worm
screw pushed up with the tyre lever (Fig.299).
Turn counter clockwise again the screw #2
(Fig.297)
Remove the screw #1 (Fig.298), put loctite on
it and tighten it FIRMLY by using the impact
air gun.
Tighten the 8mm set screw #2(Fig.297) ‘till
have it in contact with the 12mm screw #1
(Fig.298).
Lock the nut #1 (Fig.297).
Remove one by one the other three 12mm
worm screw bolts and tighten them FIRMLY
by using loctite and impact air gun.
Mount the chuck motor.
Take the protection #2, place on it the silicon
(Fig. 300) and mount it on the worm screw.
Fig.300
Take the protection #3 and place on it the
silicon (Fig.301) and mount it on the worm
screw.
Fig.301
Take the protection #4 and place on it the
silicon (Fig.302) and mount it on the worm
screw.
Fig.302
Remove the silicon in excess and use it to
cover the holes on all over the worm screw
assy (Fig.303 and 304).
Summary of Contents for KING 5600
