Service Manual 04/2010 Rev.B
61
NOTE:
After mounting the protection turn the
chuck to verify if there is contact between pulleys
and their protections. In case of contact, the
pulleys make noise, the protection need to be
readjusted until to have chuck rotation without
any noise.
5.10 TRANFORMER: CHECK AND
REPLACEMENT
:
30’
: Multimeter, small and medium cross
screwdrivers, pliers.
L
: Defective transformer may cause the
following malfunction:
1. Smoke gets out from the electric box with
consequent burning of the transformer.
2. Turning the machine on, the hydraulic motor
run but the machine does not make any
movement.
TO CONTROL THE TRANSFORMER:
Take the multimeter and select it in VAC.
Switch the machine on.
MACHINE UNDER TENSION
DANGER OF ELECTRIC SHOCK
Verify if the power between terminals 0 and
400 or 230, according to voltage at which the
machine is supplied, is correct (Fig.86): if not
see 5.1 and 5.2.
Verify if there is power between terminals 0
and 24 and between terminals 0 and 26
(Fig.86).
TO REPLACE THE TRANFORMER:
Disconnect the machine from power supply.
Open the electric box (
5.0).
Remove all wires from terminals.
Fig.86
IMPORTANT!
MARK WIRES PROPERLY FOR AN EASY AND
SAFE INSTALLATION.
Lose its four screws.
Pull the transformer up and take it out.
Install the new transformer and tighten firmly
all wires.
5.11 FUSES F4,F5,F6,F7: CHECK AND
REPLACEMENT
:
30’
:
Multimeter.
L
:
Defective fuse/s may cause the following
malfunction:
1. Turning the machine on, the hydraulic motor
run normally but the machine does not make
any movement.
TO CONTROL AND REPLACE THE FUSES:
Disconnect the machine from power supply.
Open the electric box (
5.0).
Open the protection
and remove the fuse
(Fig.87)
Fig.87
Summary of Contents for KING 5600
