Service Manual 04/2010 Rev.B
69
Tighten the wires on the switch S4
FIRMLY
.
Lock the switch S4 cover and tighten the
screws
FIRMLY
.
IMPORTANT: WHEN CLOSING THE
SWITCH DOOR BE CAREFUL NOT TO
CRUSH WIRES.
Tighten the strain cable relief leaving some
cable free.
NOTE: LEAVE 2mm OF CLEARANCE
BETWEEN SWITCH S4 AND ITS SAFETY
LEVER IN ORDER TO AVOID STOPPING OF
THE CHUCK ARM DURING THE LOWERING
OPERATION.
Verify if the shut off protection is moving up
and down freely with chuck arm completely
lowered (Fig.106).
Fig.106
5.20 EMERGENCY SWITCH S5: CHECK
AND REPLACEMENT
:
1h
:
End wrench 8mm, tube type wrench 8mm,
small standard screwdriver, small cross
screwdriver, multimeter.
:
Defective switch S5 may cause the following
malfunction:
1. Switching the machine on the hydraulic motor
turns but the machine does not work.
TO CONTROL THE SWITCH:
Remove power supply from the machine.
Remove the yellow assy from portable control
(
5.0 Fig.62).
Take a multimeter and select it in Ohm.
Leave the red emergency button unlocked
Position the multimeter probes on the red
terminals wires and verify if there is continuity
(
Ω
= 0 ~ 0,3) (Fig.107).
Do the same control on the blue terminals.
If there is not continuity the switch must be
replaced.
TO REPLACE THE SWITCH S5:
Loosen the screws #1 until to have switch
very free(Fig.107).
Loosen the metal ring #1 and turn the red
button #2 (Fig.108) counter clockwise for a
quarter of a turn pull it up to take it off.
The red button is now separated from the rest
of the switch (Fig.109).
Fig.107
Fig.108
Fig.109
Summary of Contents for KING 5600
