background image

5

Installation

• Only operate this product from the type of power source indicated on the marking 

label. If you are not sure of the type of power available, consult an electrician.

• Make sure the electrical outlet is easily accessible from the shredder.
• Shredder must be operated only in upright position.
• To make sure the shredder has proper ventilation, place it a minimum distance of 

2 in. (5 cm) from the wall or furniture.

Safety Instructions

1.  Read and follow all instructions before use. Save these instructions for later use.
2.   Always turn off and unplug the machine before moving, servicing, cleaning, or 

anything other than normal operation. Serious injury may result. Clean shredder 
with a damp cloth, using a mild soap and water solution.

3.   Do not use abrasives or petroleum-based cleaners.
4.   Place this product as close as possible to power source for quick and easy 

unplugging.

5.   Turn off the power switch before removing waste bin. It is advisable to 

disconnect the power cord before opening the shredder.

6.   This product should never be placed near a radiator or other heat source.
7.   Do not allow anything to rest on the power cord. Do not place the power cord 

where people may walk on it.

8.   If an extension cord is used with this product, make sure the total ampere (amps) 

ratings on the products plugged into the extension cord do not exceed the 
extension cord’s ampere rating.

9.   Do not attempt to service this product yourself, as opening or removing 

covers may expose you to risks of getting injured. Also, doing this will void the 
shredder’s warranty.

10.  Unplug this product and contact technical support when:
 

• The power cord or plug is damaged or frayed.

 

• Liquid has been spilled on the product.

 

• The product has been exposed to rain.

 

•  The product does not operate normally, even when the operating instructions 

are followed.

 

• The product has been dropped, or the casing has been damaged.

11.  This shredder should be operated only with an operator in attendance.
12.  Empty the waste bin regularly so that the waste output is not impeded.
13.  This machine can shred normal paper and credit cards. However, you should 

shred only one type of these items at a time to avoid causing an overload.

Summary of Contents for Nanoshred BN100P Series













Reviews: