background image

18

 

Cleaning, maintenance and repair 

 

Sprühboy 04s - Airless Edition 10.12 
 

5.1 

Cleaning intervals 

Clean  the  agent  hose  with  the  spray  gun  daily.  Use 
the cleaning adapter WRA for this purpose (1). 

 

 

5.2 

Cleaning 

 

 

There are two different kinds of cleaning 
processes: 

 

cleaning  the  spray  gun  and  agent 
hose  at  the  end  of  every  production 
run,  e.g.  if  the  filled  stainless  steel 
pressure  vessel  is  stored  in  cold 
storage and 

 

cleaning the entire implement. 

Always  clean  the  spray  gun  and  the 
agent  hose  at  the  end  of  every 
production  run  with  hot  rinsing  water 
and  a  disinfecting,  grease  solving 
cleaning agent. 

 

 

 

 

Rinse 

the 

implement 

for 

hygienic 

reasons with hot rinsing water regularly. 
Also carry out this cleaning process with 
disinfecting  cleaning  agents.  Rinse  the 
implement  very  thoroughly  with  clear 
water  after  every  use  of  disinfecting 
cleaning  agents.  Completely  spray  out 
any water  residues.  Use  compressed  air 
to blow dry the individual components. 

The  vessel  must  be  absolutely  dry 
before  it  is  filled  again.  If  even  a  single 
drop  of  water  gets  into  the  system,  this 
water  drop  could  get  lodged  in  front  of 
the  agent  nozzle  and  prevent  agent 
discharging from the nozzle. 

 

 

Summary of Contents for Spruhboy 04s Airless






























Reviews: