background image

 

Trouble shooting 

25

 

Sprühboy 04s - Airless Edition 10.12

 

Trouble shooting 

Fault 

Cause 

Remedy 

Agent  pressure  is  constantly 
dropping 

Leaks 

-  Check all visible connections. 

The agent nozzle does not spray 
evenly
 

The agent to be processed has not 
been properly mixed, e.g. clotting 

-  Check the agent to be 

processed. 

The agent is not liquid 

-  Check the agent to be 

processed. 

Agent contaminated 

-  Check the agent to be 

processed. 

Agent-nozzle clogged 

-  Check the agent nozzle, refer to 

page in this regard 21. 

Wear of the nozzle 

-  Replace the agent-nozzle. 

Deformations of the nozzle. 

-  Replace the agent-nozzle. 

No agent flow 

Agent-nozzle clogged 

-  Clean the agent-nozzle using 

hot water. 

Non-return valve in the agent 
vessel connection piece defective 

-  Replace the non-return valve. 

Suction rod clogged 

-  Dismantle the suction rod and 

clean it with hot water. 

Spray gun does not shut 

Seal kit defective 

-  Renew the seal kit. 

Closing spring in the handle of the 
spray gun defective 

-  Contact the maintenance 

service. 

The spray gun only sprays air 

The stainless steel pressure vessel 
is empty 

-  Top up with agent. 

The agent is not liquid 

-  Check the agent to be 

processed. 

Suction rod seal defective 

-  Replace the suction rod seal. 

 

Summary of Contents for Spruhboy 04s Airless






























Reviews: