background image

 

Putting into operation 

13

 

Sprühboy 04s - Airless Edition 10.12

 

4.2 

Filling the stainless steel pressure vessel 

 

Always  pull  the  bleed  valve  (1)  until  the 
excess  pressure  has  been  completely 
discharged  from  the  stainless  steel 
pressure  vessel  (2).  If  the  hissing  noise 
stops,  the  stainless  steel  vessel  has 
been  depressurised  and  you  can  open 
the pressure vessel cover. 

 

 

-  Separate  the  compressed  air  supply  from  the 

external  compressed  air  source.  Refer  to  chapter 
"Filling  the  Sprühboy  04s  with  the  required  agent 
pressure", page 14 in this regard. 

-  Pull  the  bleed  valve  (1)  until  the  hissing  noise 

stops. 

-  Swing the pressure vessel cover closure (4) to the 

top. 

 

 

 

 

-  Turn the pressure vessel cover closure (1) by 90°. 
-  Remove  the  pressure  vessel  cover  (2)  from  the 

stainless steel pressure vessel opening. 

-  Fill  the  stainless  steel  pressure  vessel  via  the 

stainless  steel  pressure  vessel  opening  at  the 
most up to the red mark (3). 

 

 

 

 

Only  fill  the  stainless  steel  pressure 
vessel  with  lump-free,  clear  products.  If 
the  product  is  not  lump-free,  the  agent 
nozzle in the spray gun will clog. 

 

-  Close the stainless steel pressure vessel with the 

pressure vessel cover (2) in reverse order. 

-  Fill  the  stainless  steel  pressure  vessel  with  an 

agent pressure of 6 bar. 

 

 

 

 

Summary of Contents for Spruhboy 04s Airless






























Reviews: