background image

IMPORTANT SAFETY INSTRUCTIONS 

 

When replacing the batteries, use the same number and the same type of batteries. 

 

Do not dispose of batteries in a fire; the battery may explode. 

 

Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin 

and eyes. 

 

A battery can present a risk of electric shock and high short circuit current. The following 

precaution should be observed when working on batteries. 
* Remove watches, rings or other metal objects. 
* Use tools with insulated handles. 

 

To prevent an overbalance of this unit, with the installation the additional stabilizer are to 

mount at the bottom side. 

 

This unit should be installed by service personnel. 

 

The equipment can be operated by any individuals with no previous experience. 

 

“The socket-outlet shall be installed near the equipment and easily accessible.” 

 

“With the installation of this equipment it should be prevented, that the sum of the leakage 

current of the UPS at the connected consumer does not exceed 3.5mA.” 

 

Attention:

 hazardous through electric shock. Also, with disconnection of this unit from the 

main, hazardous voltage still may be accessible through supply of battery. 

 

The battery supply should be therefore disconnected in the plus and minus pole through or 

from the outer enclosure accessible battery fuses when maintenance or service work 

inside the UPS is considered. 

 

The lead acid battery may cause chemical hazard. 

 

The battery presents a risk of electric shock and energy hazard. 

 

Batteries will be disposed by the manufacturer or importer.   Customers need to send 

them back with no charge for disposal. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

1

 

Summary of Contents for 5000VA























Reviews: