E
SI/200
5
21
8
11
12
23
13
16
24
RS
E
F
B
G
H
5
21
8
11
12
23
13
16
24
5
21
8
8A
11
12
23
13
16
24
1
2
4
5
6
1
2
A/200R(A/200N)
B
C
+B
5
21
8
8A
11
5
8
9
12
23
16
NO
C
NC
A
43,5
45
7,5
57
140
106
A
B
64,5
140
145
5 21 8 11 12 23 13
ON
SW1
OFF
5 21 8 11 12 23 13 16 24 RS E
E
F
5 21 8 8A 11 12 23 13 16 24
B
SW2
16 24
1 2
1 2 4 5
G
6
H
SW
1
2
5
BPT S.p.A.
30020 Cinto Caomaggiore
Venezia - Italy
12.2000/2403-1644
SI/200
2
• Residential systems using the unit
as a block selector.
Operating characteristics
• Protection of any connections
installed and management of the
engaged” signal, irrespective of
whether the unit is used as a selector
for several entry panels or as a block
selector in residential systems.
The protection mechanism is disa-
bled under the following conditions:
- approx. 2 minutes after the call;
- when the handset is replaced
(
SW1
jumper connected);
- permanently (
SW2
jumper connec-
ted).
• The selector is equipped with an
amplifier which regenerates the call
signal.
• Possibility of connecting up to
three internal units to the same call.
• Possibility of trading the origin of
an external call by means of different
tones which correspond to two diffe-
rent entry panels.
To enable this function, connect ter-
minal 8A of SI/200 selector to termi-
nal 8A on the power supplier installed
(A/200, A/241, etc.), figure 3.
In this case, connections cannot be
made for calls originating from inter-
nal floor landings.
Function of each terminal,
figure 1
Terminal block B (to power supplier or
preceding selector)
5
11V supply voltage
21
+ to entry panel
8
call 1 common
8A
call 2 common
11
audio to receiver
12
audio to entry panel
23
input 14V AC
13
door release solenoid
16
0V AC
24
engaged signal input
Terminal block E (to entry panel no. 1)
5
11V supply voltage
21
+ to entry panel
8
call common
11
audio to receiver
12
audio to entry panel
23
output 14V AC
13
door release solenoid
16
0V AC
24
engaged signal output
RS
reset
(
1
)
E
audio enable
(
1
) Functions for combined (audio
and video entry systems) installa-
tions.
Terminal block F (to entry panel no. 2
or subsequent selector)
5
11V supply voltage
21
+ to entry panel
8
call common
11
audio to receiver
12
audio to entry panel
23
output 14V AC
13
door release solenoid
16
0V AC
24
engaged signal output
Terminal block G (services)
1
call 1 input
2
call 2 input
4
engaged signal output (for resi-
dential systems)
5
general reset
6
enable output
Terminal block H (services)
1
call 1 output
2
call 2 output
1
GB
INSTALLATION
INSTRUCTIONS
SI/200 ENTRANCE SELECTOR
This unit permits the selection of two
entry panels and is configured to
create the following systems:
• Single or multi-family systems with
several entrances using the same
number of selectors as there are
entry panels minus one.
SW jumpers functions,
figure 1
(in ON position)
SW1
resetting of engaged entry
panels by replacing the hand-
set.
SW2
deactivation of call protection
and engaged signal.
NOTE. The selector is supplied with
SW1 jumper wired in.
When A/241 power supplier are
used (1+n installations), the SW1
jumper must be connected, figure
1.
Technical features
• Supply voltage: 11 V DC.
• Current demand: 45 mA max. (5
mA quiescent).
• Working temperature range: from
0 °C to +35 °C.
• Dimensions: 8 DIN units, low profi-
le module, figure 2.
The unit can be installed without
terminal covers into boxes provi-
ded with DIN rail (EN 50022).
Dimensions are shown in figure
2A.
It can also be surface mounted,
using the DIN rail supplied, but fit-
ted with terminal covers.
Dimensions are shown in figure
2B.