3 4 5 6 8 8A 11 12 23 14 13 16 24
3 4 5 6 8 11 12 23 14 13 16 24
3 4 5 6 8 11 12 23 14 13 16 24
1
2 3 4 5 6 7 8
1
2
G
H
F
E
B
SW1
SW2
SW3
SW4
SW5
ON
OFF
A
B
D
C
5
6
21
8
8A
22
11
12
23
14
13
16
3
4
7
5
6
8
9
SW
B
3
4
5
6
8
8A
11
12
23
14
13
16
24
VA/200
VSI/200
43,5
45
7,5
57
210
106
A
B
64,5
210
145
1
2
3
12.2000/2402-9844
2
GB
INSTALLATION
INSTRUCTIONS
VSI/200 ENTRANCE SELECTOR
This unit permits the selection of
two entry panels and is configured
to create the following systems:
• Single or multi-family systems
with several entrances using the
same number of selectors as there
are entry panels minus one.
• Residential systems using the
unit as a block selector.
Operating characteristics
• Sequential selection of entry
panel or supplementary camera by
the monitor.
• Protection of any connections
installed and management of the
engaged signal irrespective of
whether the unit is used as a selec-
tor for several entry panels or as a
block selector in residential
systems (the protection may be
disabled by connecting jumper
SW2
, figure 1).
• The selector is equipped with an
amplifier which regenerates the
call signal.
• Possibility of connecting up to
a
ni
-
i
-
la
le
o
A
:
à
l-
-
N
o
a
N
il
o
three internal units to the same call.
• Possibility of trading the origin of
an external call by means of diffe-
rent tones which correspond to two
different entry panels.
To obtain this function: connect ter-
minal
8A
of VSI/200 selector to ter-
minal
8A
of VA/200 power supplier
(terminal board B) and remove the
jumper
SW
from VA/200 power
supplier as shown in figure 2.
WARNING. A differentiated landing
call tone is not available in this con-
figuration.
Function of each terminal,
figure 1
Terminal block B (to power supplier
or preceding selector
3
video signal
(
1
)
4
video signal shield
5
17,5 supply voltage
6
+ to entry panel
8
call 1 common
8A
call 2 common
11
audio signal to monitor
12
audio signal to entry panel
23
auxiliary door release button
14
entry panel activation
13
+ 12V supply voltage to
16
door release solenoid
24
engaged signal input
Terminal block E (to entry panel no. 1)
Terminal block F (to entry panel no.
2 or subsequent selector)
3
video signal
(
1
)
4
video signal shield
5
17,5V supply voltage
6
+ to entry panel
8
call common
11
audio signal to monitor
12
audio signal to entry panel
23
auxiliary door release button
14
entry panel activation
13
+ 12V supply voltage to
16
door release solenoid
24
engaged signal output
f
d
s
e
e
e
y
y
s
e
f
-
a
l
e
r
n
e
o
(
1
) coaxial cable connection; twisted
pair connection to terminal blocks
B-E-F:
3
positive video signal
4
negative video signal
Terminal block G (services)
1
call 1 input
2
call 2 input
3
12V DC power input
4
engaged signal output (for
residential systems)
5
general reset
6
changeover enable-next selec-
tor
7
changeover enable-previous
selector
8
entry panel selection
Terminal block H (services)
1
call 1 output
2
call 2 output
SW jumper functions,
in ON posi-
tion, figure 1
1
repositioning of selectors fol-
lowing scanning of entry
panels activatedby the monitor
(only the jumper of the last
selector must be set in position
ON while all preceding selec-
tors must be set to OFF).
2
deactivation of call protection
and engaged signal.
3
resetting of engaged entry
panels on audio entry systems
by replacing the handset.
4-5
activation of general reset (on
residential systems.
NOTE. The selector is supplied
with SW1 jumper wired in (installa-
tion with 2 entry panels).
Technical features
• Supply voltage: 14,5÷17,5VDC
or 12VDC.
• Current demand: max. 80mA
(7mA quiescent).
• Working temperature range:
from 0 °C to +35 °C.
• Dimensions: 12 DIN units, low
profile module, figure 3.
The unit can be installed without
terminal covers, in boxes fitted
with DIN guide (EN 50022).
See figure 3A for overall dimen-
sions.
Alternatively, it can be wall-
mounted using the DIN guide
provided, and applying the ter-
minal cover.
See figure 3B for overall dimen-
sions.
VSI/200
BPT S.p.A.
30020 Cinto Caomaggiore
Venezia - Italy