background image

29

6.  Install thrust washer (Item 65), onto the second stage 

planet assembly (with output sun gear).  A light coat 

of oil soluble grease should be used to hold it in place 

during assembly.  Slide the planet assembly into the 

ring gear and engage the output sun gear with the 

output planet gears.  The second stage planet gears 

should now be at least 1/8 inch (3 mm) below the top 

of the teeth cut into the ring gear.  If they are above the 

ring gear teeth, the unit is not properly assembled to 

this point.  Either the thrust washer (Item 65) is improp-

erly positioned, or the output planet carrier is not fully 

engaged onto the motor support (possibly caused by 

the split ring not being fully seated).  Remove the sec-

ond stage planet assembly and/or the output planet 

assembly to determine and correct the cause of the 

problem before proceeding.

7.  Install thrust washer (Item 57) onto the primary planet 

assembly (with second stage sun gear).  A light coat 

of oil soluble grease should be used to hold it in place 

during assembly.  Install the primary planet assembly 

onto the second stage planet assembly, engaging the 

second stage sun gear with the second stage planet 

gears.  Visually check to be sure the thrust washer is 

properly positioned.

8.  Install the primary sun gear (Item 55) through the cen-

ter of the primary planet assembly.

9.  Carefully set the cover (Item 42) onto the main ring 

gear, engaging the primary planet gears with the gear 

teeth machined into the cover.  Turn the cover to align 

the bolt holes with those in the main ring gear and in-

stall all 12 capscrews and lockwashers (Items 43 and 

44).

In the following step, the primary ring/cover may sud-

denly drop on the main ring gear when all primary sun 

gear teeth are aligned with those in the cover.  DO NOT 

work with your fingers between the cover and the main 

ring gear.

CAUTION

Summary of Contents for CH330





































Reviews: