background image

5

GENERAL SAFETY RECOMMENDATIONS

Safety for operators and ground personnel is of prime concern. Always take the necessary precautions to ensure safety 

to others as well as yourself. To ensure safety, the prime mover and winch must be operated with care and concern by 

the operator for the equipment, and a thorough knowledge of the machine’s performance capabilities. The following 

recommendations are offered as a general safety guide. Local rules and regulations will also apply.

1.  Read all warning tag information and become familiar 

with all controls before operating winch.

2.  Never attempt to clean, oil or perform any mainte-

nance on a machine with the engine running, unless 

instructed to do so in the service manual.

3.  Never operate winch controls unless you are properly 

seated at the operators station on the prime mover and 

you are sure personnel are clear of the work area.

4.  Assure that personnel who are responsible for hand 

signals are clearly visible and that the signals to be 

used are thoroughly understood by everyone.

5.  Ground personnel should stay in view of the prime 

mover operator and clear of winch drum. Do not al-

low ground personnel near winch line under tension. A 

safe distance of at least 1-1/2 times the length of the 

cable should be maintained. 

6.  On machines having hydraulically, mechanically and/

or cable controlled equipment, be certain the equip-

ment is either lowered to the ground or blocked se-

curely before servicing, adjusting and/or repairing the 

winch. Always apply the prime mover parking brakes 

and lower equipment before dismounting the prime 

mover.

7.  Inspect rigging, winch and hydraulic hoses at the be-

ginning of each work shift. Defects should be correct-

ed immediately.

8.  Keep equipment in good operating condition. Perform 

scheduled servicing and adjustments listed in the  

Preventive Maintenance  section of this manual.

9.  An equipment warm-up procedure is recommended 

for all start-ups and is essential at ambient tempera-

tures below +40°F (4°C). Refer to “Warm-Up Proce-

dure” listed in the Preventive Maintenance section of 

this manual.

10. Be sure of equipment stability before operating winch.
11. The winches described herein are neither designed 

nor intended for use or application to equipment used 

in the lifting or moving of persons.

12. Do not exceed the maximum pressure (PSI or kPa) or 

flow (GPM or LPM) stated in the winch specifications.

13. Operate winch line speeds to match job conditions. 
14. Leather gloves should be used when handling winch 

cable.

15. Never attempt to handle winch cable when the hook 

end is not free. 

16. When winding winch cable on the winch drum, never 

attempt to maintain tension by allowing winch cable 

to slip through hands. Always use the hand-over-hand 

technique.

17. Never use winch cable with broken strands.  Replace 

winch cable. 

18. Do not weld on any part of the winch.
19. Do not use knots to secure or attach winch cable. 
20. Use recommended hydraulic oil and gear lubricant.
21. Keep hydraulic system clean and free from contami-

nation at all times.

22. Use correct size cable anchor for cable and pocket in 

winch drum.

23. The BRADEN wire rope anchors are capable of sup-

porting the rated load when installed properly. For ad-

ditional  safety, ALWAYS  maintain  a  minimum  of  five 

wraps of wire rope on the drum.

Safety Informational callouts used in this manual in-

clude the following:

Failure to obey the following safety recommendations may 

result in property damage, personal injury, or death.

CAUTION

 – This emblem warns against potential or 

unsafe practices which COULD result in personal in-

jury and product or property damage if proper proce-

dures are not followed.

CAUTION

WARNING

 – This emblem warns against hazards and 

unsafe practices which COULD result in severe per-

sonal injury or death if proper procedures are not fol-

lowed.

Summary of Contents for CH330





































Reviews: