INSTALLATION GUIDE
Skylight
6
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
6
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
6
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
6
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
10
ADJUST THE SHADE
Tension Cords
The moving rail should slide easily, yet hold its position when it is released. Adjust the
tension cords in the anchor rail if the moving rail does not slide properly.
Move the slip knot to the right to increase the cord tension. Do not stretch the
N
spring to a length greater than 5
½
".
Move the slip knot to the left to decrease the cord tension.
N
Moving Rail
The moving rail should be parallel to the anchor rail so that the two rails make even
contact when the shade is closed. Adjust the moving rail if it is not parallel.
Loosen the cord clamping screw.
N
Slide the cord between the two washers.
N
CAUTION:
Do not adjust the cord tension while you make this adjustment.
Support Cord Tension (If Applicable)
If your shade has a support cord, it should be very taut. To adjust:
Loosen the support cord clamping screw.
N
Pull the cord through the two washers to the desired tension.
N
Tighten the screw.
N
Make sure the cord is held taut between the two washers.
N
Cord Clamping Screw
And Washers
Slip Knot
Tension Spring
Clamping
Screw
Support
Cord
Washers
