background image

4

www.bradleycorp.com

15

LISTA DE PIEZAS BÁSICAS

Número de referencia

1

2

3

3

4

4

5

5

6

6

7

8

9

10

11

12

13

Descripción

Carcasa de hierro fundido, automático - Blanco

Carcasa de hierro fundido, Pulsador - Blanco

Motor - UL

Motor - CE

Resistencia - UL

Resistencia - CE

Temporizador - UL

Temporizador - CE

Sensor - UL

Sensor - UL

Escobillas

Turbina

Fusible - UL

Llave

Silent Blocks

Muelle del motor

Cable del sensor

Código de pieza Bradley

P15-420

P15-421

P15-422

P15-423

P15-424

P15-425

P15-426

P15-427

P15-428

P15-429

P15-417

P15-430

P15-431

P15-419

P15-444

P15-446

P15-447

METHOD OF USE

Correct cleaning of the unit will lengthen its working life considerably.
When in use, the machine will accumulate dust inside which should be cleaned out every six months.

PREVENTATIVE MAINTENANCE AND CLEANING

Sensored

1. Preventative maintenance

2. Cleaning Method

Sensored models

1. Turn off power to the unit.
2. Remove cover using security wrench (See Dismantling for Installation).
3. Clean away any accumulated dust on the fan with a soft bristle brush while rotating it manually. Use

the same brush, to clean away all accumulated dust from the other components. Carefully remove
any dust from the electronic circuit board and hand detecting sensors using a fine brush.

4. Use brush to clean the air inlet grill and make sure the LED visor is completely clean.
5.  Check the condition of the motor brushes. These should be replaced when they are less than 13/64
inches (5 mm.).
6.  Reconnect power to the unit and let it run continuously, removing any excess dust.
7. Turn off power to the unit and install cover per the Mounting Instructions.

Caution: Do not damage or force any components.

Cleaning the cover - Use only a wet cloth to clean the covers. Do not use any kind of detergent, acids,
lye, abrasives, hydrocloric acid, etc.

These models operate by hand detection. Place hands 2-6 inches (5 - 15 cm) from the
air outlet and the dryer will start working. Once activated, immediately place hands in
air flow and rub together until dry. This machine will stop 2-3 seconds after use.

NOTE: Vandal Resistant Operating System will cause this unit automatically shut-off if
sensor is completely blocked.

Push Button models

These models operate by push button activation. Once activated, immediately place
hands in air flow and rub together until dry. The dryer cycle time lasts 34 seconds, if
additional time is needed, push button to activate unit again.

Push Button

For Warranty information go to:

www.bradleycorp.com/customerservice/warranty-dryers.jsp

WARRANTY

3

5

4

1

2

6

7

8

10

9

11

12

13

distributed by 

 RESTROOM DIRECT       704 . 937. 2673      

www.

RestroomDirect

.com

Summary of Contents for 2903-280000











Reviews: