Bradley Express SS-3N/BIR3/WH Installation Manual Download

Page: 4 / 15

SS-3N/BIR3/STD, SS-3N/BIR3/WH

Installation

9/7/2018

Bradley

• 215-1496 Rev. J; ECN 17-08-026

Supplies Required

• (8) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum pull-out rating

of 1,000 lbs.)

• STD. HEIGHT ONLY: (2) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount scuff base to wall
• ½" nominal copper tubing for hot and cold supplies and 1½" NPT drain piping

Dimensions - Front and Top Views

SOAP

Top View

80" (2032)

Front View

Standard Frame

Front View

Wall-Hung Frame

8-5/8" (219)

30" (762)

8" (203)

51-1/4" (1302)

58" (1473)

64" (1626)

68-1/4" (1734)

8" (203)

68-1/4" (1734)

58" (1473)

64" (1626)

8" (203) Radius

10" (254) Radius

30" (762)

(mm)

Summary of Contents for Express SS-3N/BIR3/WH
















Search results

Summary of Contents for Express SS-3N/BIR3/WH

Reviews:

Related manuals for Express SS-3N/BIR3/WH

Brands by name

Popular brands

Bradley Express SS-3N/BIR3/WH, Installation Manual

Search results

Summary of Contents for Express SS-3N/BIR3/WH

Reviews:

Related manuals for Express SS-3N/BIR3/WH

Brands by name

Popular brands