background image

LVAD3 

Installation

12

 

4/17/2017

 Bradley 

• 215-1851 Rev. A; ECN 17-08-002

Install access panel brackets 
to wall using #10 fasteners 
(supplied by installer) as 
shown in rough in drawing. 
Install top screw into slot. Do 
not install bottom screw until 
Step C is complete.

A

Make all connections before installing access panel.

Access Panel

7

#10 Top 

Screw

Shown in closed 

position. Rotate 

90° to Open

Insert #10 thumbscrews 
into front bowl apron as 
shown. Thumbscrew in 
vertical position is closed. 
Thumbscrew in horizontal 
position is open.

B

Hang access panel onto 
mounting brackets attached 
to the wall on the left and 
right sides. Rotate panel up 
and check fitup between 
thumbscrews and panel slots. 
Rotate access panel down 
and make adjustment to 
brackets if necessary. Install 
bottom #10 fastener into 
brackets.

C

Rotate access panel up 
and secure by rotating 
thumbscrews to the closed 
position.

E

To open access panel, rotate 
thumb screw, slightly push 
panel up and swing access 
panel down. Do not remove 
thumbscrews.

F

#10 

Thumb 

Screw

CAUTION For applications where children are present or for applications 

subject to vandalism, order security screw option S45-2880.

Attach P-trap to drain adapter 
and waste outlet.

D

For ease of installation, lift trap cover up at bottom, while positioning 
over thumb screw. Start at center and move left to right.

Summary of Contents for Verge LVA Series














Reviews: