background image

10

SEELEY INTERNATIONAL –

 

HOME OWNER’S MANUAL

SETTING THE AUTO 

PROGRAMS - MULTIPLE SCC'S

Enter Program Setting Mode

1

  Press the ON/OFF button on the 

    "Master" SCC. The "Master" SCC

    must be ON to enable "Slave"    

    controls to be turned ON.

2

  Press the ON/OFF button on SCC 

    you wish to program toturn it ON.

3

  Press the SET button and hold for 3 

    seconds - the SCC will enter 

    program setting mode, SET & MON 

    will flash).

Select Day or Group of Days to 

Program

1

  Press the UP or DOWN arrow 

    buttons to scroll through the day 

    selection options:
     •  Individual days - MON, TUES, 

        WED, THU, FRI, SAT, SUN
     •  Blocks of days - [MON-FRI], 

        [SAT-SUN], MON-SUN]

2

  Press SET when the required day or 

    group of days is displayed.

Set WAKE Period Program 

Values

Set WAKE period start time:

1

  Press UP or DOWN arrow buttons to 

     adjust to required start time for

     displayed time period.

2

  Ensure that 'AM' or 'PM' is correct.

3

  Press SET when the required start        

    time is displayed.
Set WAKE period temperature:

1

  Press UP or DOWN arrow buttons to 

    adjust to required set temperature for 

    displayed time period.

2

  Press the ON/OFF button on the 

    "Master" SCC. The "Master" SCC 

    must be ON to enable "Slave" 

    controls to be turned ON.

3

  Press the ON/OFF button on SCC 

    you wish to program toturn it ON.

4

  Press SET when required 

    temperature is displayed.

Set Program Values for AWAY, 

HOME and SLEEP periods

1

  Repeat the above steps for AWAY, 

    HOME and SLEEP time periods.

2

  The SCC will automatically advance 

    to the next time period once the 

    previous one has been set.

3

  The SCC will automatically exit 

    program setting mode once all time 

    periods have been set.

Set Program Values for 

Remaining SCC's

1

  Repeat the above steps for all other    

    SCC's on the system.

2

  Each can be set with its own times 

    and temperatures, independent of 

    others SCC's on the system.

HEATING

Summary of Contents for Spectrolink





































Reviews: