Braemar Spectrolink Owner'S Manual Download

Page: 32 / 36

Spectrolink Comfort Control

MANUAL MODE OPERATION

When operating in MANUAL mode the

cooler will turn on and off to maintain

the set temperature until turned off by

the user.

WARNING:

Seeley International

recommends that maintenance is

carried out by an authorised service

agent. Climbing onto the roof is

hazardous and could result in personal

injury or property damage. Failure to

have maintenance carried out may

affect your warranty coverage. The

following instructions are provided for

you to pass on to your service agent, if

required, to ensure that the correct

maintenance is carried out.

Turning the Cooler ON

Press the ON/OFF button.

Press and hold the SET button and

press the MAN/AUTO button to set

the remote control to MAN mode (the

MAN/AUTO button must be pressed

within less than 3 seconds of

pressing the SET button).
• If the set temperature is less than

the room temperature the room

fan and cooler compressor will

start.
• The snowflake and room fan

symbols will appear.

• The SCC has a built-in 2 minute

delay to prevent the compressor

from re-starting within less than 2

minutes of last turning off - this is

to prevent damage to the

compressor.

Turning the Cooler OFF

Press the ON/OFF button.

• The display will revert to OFF

mode.
• The room fan and compressor will

turn off immediately.

Adjusting the Room Temperature

Decrease set temperature: Press the

DOWN arrow to decrease set

temperature by 1ºC.

Increase set temperature: Press the

UP arrow to increase set

temperature by 1ºC.

Adjusting the Fan Speed

With the SCC on press and hold the

FAN button for 3 seconds - the fan

speed and fan symbol will flash.

Press the up or down arrow buttons

to adjust to the required fan speed -

adjustable between 3 and 10 in

refrigerated cooling mode.
• The SCC will revert to the normal

ON state after a few seconds.
• The fan speed is not

user-adjustable in multiple SCC

systems.

Using HOME/AWAY in MANUAL

Mode

The HOME/AWAY button alllows you to

set and switch between two

temperature settings as follows:

When HOME is selected adjust to

the required "HOME" set

temperature.

When AWAY is selected, adjust to

the required "AWAY" set

temperature.

Press HOME/AWAY to switch

between these settings.

REFRIGERATED COOLING

Summary of Contents for Spectrolink





































Search results

Summary of Contents for Spectrolink

Reviews:

Related manuals for Spectrolink

Brands by name

Popular brands

Braemar Spectrolink, Owner'S Manual

Search results

Summary of Contents for Spectrolink

Reviews:

Related manuals for Spectrolink

Brands by name

Popular brands