background image

Compact manual wheelchair tie-downs

Compact manual wheelchair tie-downs

W

ar

ran

ty

19

After care

18

Warranty

BraunAbility products are extensively tested using BraunAbility 

anchorage systems, and our full warranty normally only applies 

to BraunAbility equipment when used with BraunAbility branded 

anchorages or as instructed. BraunAbility have also participated in test 

programs with other manufacturers anchorage products and will support 

warranty on the BraunAbility products when used in conjunction with 

such jointly tested systems. For further details on specific applications 

please contact the Sales Office. In other situations, using BraunAbility 

products, for which BraunAbility has not participated in a joint test 

program, a limited BraunAbility warranty will apply.

Equipment storage and maintenance

• 

Store the restraint safely in supplied bag, off the floor, to avoid 

damage and ensure that it cannot become a projectile in an accident. 

• 

Regularly inspect the wheelchair restraint systems for damage, wear 

or malfunction. If any problems are identified replace components 

immediately. 

• 

When not in use, keep loose occupant webbing ends connected 

to their corresponding buckle sleeves, etc, to prevent them from 

becoming trip hazards and from flailing around when the vehicle is in 

motion. 

• 

All webbing and components can be cleaned as necessary, but care 

should be taken to prevent contamination of the webbings with 

polishes, oils and chemicals, particularly battery acid. 

• 

To clean the straps use warm soapy water and a clean soft cloth. Rinse 

with clear water and allow to air dry. To disinfect, use a mild spray 

disinfectant and do not use products containing bleach.

 

Important: 

when cleaning or disinfecting, do not immerse or flood buckles, 

karabiner fittings or floor anchors in the disinfectant or water.

 

• 

If the vehicle is involved in an accident when any restraints are 

deployed, remove them from service and replace immediately. If in 

doubt please contact BraunAbility.

Summary of Contents for T-ROBJ























Reviews: