200 SERIES TWO-MAN AUGERS
FORM GOM08042004US, VERSION 1.1
English-EN
7
ACCESSORIES
NOTE:
All auger bits, bit extensions, teeth and bit screws are for use in general
purpose projects for a variety of soil conditions unless otherwise specified. All
auger bits and auger bit extension drive connections are shown below are 1-3/8
inch (35 mm) hexagon. Digging depth for all augers is 36 inches (914 mm).
Planting auger digging depth is 30 inches (762 mm) and auger bit extension is
15 inches (381 mm).
Part #
Description
Cutting
Diameter
Weight
(in lbs)
BR10586
4 inch (102
mm) Auger OD
4.5 inch
(114 mm)
19.0
BR10587
6 inch (152
mm) Auger OD
7.5 inch
(191 mm)
24.0
BR10588
8 inch
(203mm)
Auger OD
9.5 inch
(241 mm)
30.0
BR10589
10 inch (254
mm) Auger OD
11.6 inch
(295 mm)
36.0
BR10590
12 inch (305
mm) Auger OD
13.6 inch
(345 mm)
48.0
BR10591
14 inch (356
mm) Auger OD
15.6 inch
(396 mm)
54.0
BR10592
16 inch (406
mm) Auger OD
17.2 inch
(437 mm)
61.0
BR10593
18 inch (457
mm) Auger OD
19.7 inch
(500 mm)
40.0
5500-
15XBR
No Flighting
Auger Bit
Extension
NA
7.1
BR10614
Standard Dirt
Tooth
NA
3.0
BR10615
Hardfaced Dirt
Tooth
NA
3.2
BR10616
Chisel Type
Dirt Tooth
NA
1.2
BR10617
Tungsten
Carbide Dirt
Tooth
NA
1.3
BR10618
Tungsten
Carbide Tooth
NA
1.2
BR10619
Screw Bit
NA
2.6
BR10620
Hardfaced
Screw Bit
NA
1.0
BR10621
Bit Screw
NA
4.2
BR10622
Hardfaced
Screw Bit
NA
1.5
BR10623
Bit Screw
NA
1.6
BR10624
Hardfaced
Screw Bit
NA
1.9
BR10625
Bit Screw
NA
3.2
BR10626
Hardfaced
Screw Bit
NA
4.5
BR10628
Auger Pin
NA
0.4
8 MACHINE SET-UP
Open shipping carton immediately upon receipt. Remove Auger from carton.
Visually inspect contents of carton for freight damage and/or missing parts. If
shipping damage is evident, contact delivering carrier immediately to arrange
for an inspection of damage by their claims representative. DO NOT DESTROY
OR DISCARD SHIPPING CARTON UNTIL INSTRUCTED BY AUTHORIZED
REPRESENTATIVE OF CARRIER OR FACTORY. If missing parts are
detected, notify your dealer who will assist you in obtaining them.
INSTALLING OPERATOR HANDLES
Tools Required:
2 each, 1/2 inch (13 mm) wrench
1 each, 5/16 inch (8 mm) wrench
1 each, torque wrench, 240 inch pounds (27 Nm) capacity with 1/2 inch
(13 mm) socket
1 each, small Phillips screwdriver
1 each, small vice grip pliers
1 each, cut off pliers
Assemble operator handles to transmission on level working platform of
appropriate size and height. As an alternative, transmission driveshaft can be
securely mounted in suitable bench vice.
1.
Open assorted hardware bag into suitable container to prevent
component loss.
2.
Facing spark plug end of engine, install two curved non-throttle control
operator handles into transmission case sockets, arc of curve pointing
upward. Use supplied nuts, lock washers and flat washers with threaded
end of bolts facing upwards. FINGER TIGHTEN ONLY. DO NOT FINAL
TORQUE FASTENERS AT THIS TIME. FIGURE 2
FIGURE 2
3.
Facing fuel tank end of engine, install remaining curved non-throttle
operator handle into transmission case socket located under engine
governor control on left side per Step 2.
4.
Install throttle control handle with throttle control grip in remaining
transmission case socket. Auger is designed for throttle control grip to be
operated by the right hand. DO NOT deviate from assembly and
operation of throttle control outlined in this manual. Reduced control of
Auger will result.
5.
Using torque wrench, torque all handle screws evenly to 240 inch pounds
(27 Nm).
DANGER
•
Improper assembly and operation of Magura® throttle
control will reduce controllability of Auger, resulting in
property damage and/or personal injury.
CAUTION
•
Properly attached operator handles provide proper structural
integrity.
•
Use of Hole Digger without operator handles properly
attached can result in handle failure and/or personal injury.