BRAYER BR4001, Instruction Manual

8

9

EN

EN

released from the openings of the soleplate (11) only 

if the iron is in horizontal position. To stop the steam 

supply, put the iron vertically or set the knob (3) to the 
position «  » (steam supply is off).

• 

After you finish ironing, set the continuous steam 
supply knob (3) to the position «  » (steam supply 

is off).

• 

Disconnect the power plug from the mains socket 

and wait until the iron soleplate (11) cools down 

completely.

ATTENTION!

If steam is not supplied during the operation, check 

whether the steam supply knob (3) are set properly and 

whether there is water in the water tank (10).

Note: 

- if you are going to iron delicate fabrics after the 

soleplate (11) heats up, it is recommended to wait for 

the next cycle of the indicator (6) switching off.

WATER SPRAY

• 

Make sure that there is enough water in the water 

tank (10).

• 

Press the water spray button (5) to dampen the 

fabrics.

BURST OF STEAM

• 

The burst of steam is useful for ironing folds.   

• 

When pressing the burst of steam button (4) steam 

will go out of the iron soleplate (11) openings 

intensively.

Note:

 to avoid water leakage from the soleplate (11) 

openings, press the burst of steam button (4) with 4-5 

sec. intervals.

VERTICAL STEAMING

• 

Hold the iron vertically at the distance of 5-20 cm 

from the clothes or interior objects and press the 

burst of steam button (4) with 4-5 second intervals, 

steam will be released from the soleplate (11) 

openings intensively.

ATTENTION!

- To avoid fabric melting, do not touch it with the iron 

soleplate (11) while steaming.
- Do not steam clothes on a person. Use a clothes 

hanger or a coat rack.

• 

After you finish ironing, switch the iron off and 

unplug it, wait until the iron soleplate (11) cools down 

completely, then open the water inlet lid (2), turn over 

the iron and drain the remaining water.

AUTOMATIC SWITCH OFF

• 

The iron has 2 automatic switch off modes.

1. If the iron is set in horizontal position and remains 

still for 30 seconds, the iron’s heating element will be 

switched off, and the indicator (6) will be flashing.

2. If you set the iron in vertical position on the base 

(9) and leave it for 8 minutes, the heating element will 

switch off and the indicator (6) will be flashing.

• 

To resume ironing set the iron from horizontal 

position to vertical or vice versa, wait until the iron 

soleplate (11) heats up and continue ironing.

STEAM CHAMBER CLEANING

• 

Regularly clean the steam chamber of the iron, 

especially in the regions with «hard» tap water.

• 

Set the continuous steam supply knob (3) to the 
position «  » (steam supply is off).

• 

Open the lid (2), fill the tank with water up to the 

maximal mark «МАХ» and close the lid (2).

• 

Place the iron on its base (9).

• 

Insert the power plug into the mains socket, the 

indicator (6) will light up.       

• 

When the iron soleplate (11) reaches the set 

temperature, the indicator (6) will go out and you can 

start cleaning the steam chamber of the iron.

• 

Remove the power plug from the mains socket.

• 

Hold the iron above the sink horizontally, press and 

hold down the button (12) «Self -Clean».

• 

Boiling water and steam with scale will be intensively 

released from the soleplate (11) openings.

• 

Slightly sway the iron back and forth, until all the 

water leaves the water tank (10).

• 

Place the iron on its base (9) and let the soleplate 

(11) cool down completely.

• 

After the soleplate (11) cools down, wipe it with a dry 

cloth.

• 

Before taking the iron away for storage make 

sure that the water tank (10) is empty, andthe iron 

soleplate (11) is dry.

CLEANING AND MAINTENANCE

• 

Before cleaning make sure that the iron is switched 

off and cold and the power plug is not connected to 

the mains socket.

• 

Wipe the iron body with a slightly damp cloth and 

then wipe it dry.

• 

You can remove the mineral deposit from the iron 

soleplate (11) with a cloth soaked in table vinegar.

• 

•After removing the mineral deposit polish the 

soleplate (11) surface with a dry clean cloth.

• 

Do not use abrasives or solvents to clean the iron 

soleplate (11) and body.

• 

Avoid contact of the iron soleplate (11) with sharp 

metal objects, as well as with metal buttons, zippers 

etc.

• 

Do not immerse the iron, the power cord and the 

power plug into water or any other liquids.

STORAGE

• 

Before taking the iron away for storage drain the 

remaining water from the water tank (10) and clean 

the iron.

• 

Set  the continuous steam supply knob (3) to the 
position «  » (the steam supply is off).