background image

  

23 

10 SAFETY FORM 

 

WARNING 

A complaint will only be handled by Bredel if this Safety Form is fully completed and 
digitally send to Bredel before shipment is activated. A hardcopy of this form is to be 
attached to the outside of the packaging including MSDS sheet or similar safety 
information sheet if applicable for each item returned. 

 

Product Use and Decontamination Declaration 

 

In  compliance  w ith our 

Health & Safety Regulations

, the user is required  to declare any substances that have been in 

contact w ith the item(s)  being returned to Watson-Marlow  Bredel  B.V. or any of its subsidiaries or distributors. Not  follow ing 
these requirements  may  lead to delays in service and/ or response time.  Full  completion  of this form assures w e are 
provided w ith necessary information  before receipt of the item(s) being  returned. A hardcopy of the completed  form must  be 
attached to 

the outside of the packaging

 containing  the item(s). The  sender of the item(s) is responsible  for cleaning  and 

decontaminating  of the item(s) before returning  them  in such w ay that it is safe for the receiver to open the packaging  and 
handle  the item(s). 

Com plaint num ber:

 ........................... 

1. 

Company: 

…………………………………………………………………………….……………………….…………… 

Address: 

...……………………………….……. 

Contact  person: …….………………………………. 

Telephone: 

………….…………………………… 

Postal  code: 

………………..………………………………… 

Email  address: ………………..……………………………… 

Fax number: 

..………………………………………………... 

2. 

Product: 

…………………………………….… 

3.4  Cleaning  fluid to be used if residue of chemical  is found 

during service: 

(a) 

……………………………………………….… 

(b) 

……………………………………………….… 

(c) 

…………………………………………….…… 

(d) 

…………………………………….……….… 

2.1 

Serial  Number:……………………………………. 

2.2  Has the Product  been used? 

 

Yes 

(Go to section 3) 

 

No 

(Go to section  5) 

3. 

Details  of substances pumped 

4. 

 

I  hereby  confirm  that  the  only  substance(s)  that  the 
equipment  specified  has  pumped  or  come  into 
contact w ith those named, that the infor mation given 
is  correct  and  the  carrier  has  been  informed  if  the 
consignment  is of a hazardous nature. 

3.1  Chemicals  names: 

(a) 

………………………………..……..………. 

(b) 

……………………………….………………. 

(c) 

…………………………………….…....…… 

(d) 

..…………………………………...…………. 

5. 

Signed:   

……………………………..…………… 

Name: 

…………………..……...………………. 

Position: 

………………………………..………… 

Date: 

……………………………….…………. 

3.2  Precautions  to be taken in handling  these 

substances: 

(a) 

……………………………………………….. 

(b) 

…………………………………………….…. 

(c) 

……………………………………………….. 

(d) 

……………………………………………….. 

 

Note: 

To assist us in our service, please describe any fault 
condition you have w itnessed. 

…………………………………………………………… 

…………………………………………………………… 

…………………………………………………………… 

…………………………………………………………… 

Quantity  of sheets attached:  

………………………… 

3.3  Actions to be taken  in event of human  contact: 

(a) 

……………………………………………….. 

(b) 

…………………………………………….…. 

(c) 

……………………………………………….. 

(d) 

……………………………………………….. 

Summary of Contents for PD/100

























Reviews:

Related manuals for PD/100