background image

  

3  WARRANTY  CONDITIONS 

The manufacturer offers a two year warranty on all parts of the pulsation damper. This means that all 
parts will be repaired or replaced free of charge with the exception of consumables, such as hoses 
and seals, or parts which have been misused or have been intentionally damaged.  If parts are used 
that are not Watson-Marlow Bredel B.V. (hereafter called Bredel) parts, every warranty becomes void. 

Damaged parts which are covered by the applicable warranty conditions can be returned to the 
manufacturer. The parts must be accompanied by a fully filled in and signed safety form, as present in 
the back of this manual. The safety form must be applied to the outside of the shipping carton. Parts 
which have been contaminated or which have been corroded by chemicals or other substances which 
can pose a health risk, must be cleaned before they are returned to the manufacturer. Furthermore, it 
should be indicated on the safety form which specific cleaning procedure has been followed, and it 
should be indicated that the equipment has been decontaminated. The safety form is requir ed at all 
items, even if the parts have not been used. 

Warranties purporting to be on behalf of Bredel B.V. made by any person, including representatives of 
Bredel, its subsidiaries, or its distributors, which do not accord with the terms of this war ranty shall not 
be binding upon Bredel unless expressly approved in writing by a Director or Manag er of Bredel. 

Summary of Contents for PD/100

























Reviews: