RF Remote Control Switch
Set RCS 1000 N
User manual
User manual RF Remote Control Switch Set RCS 1000 N
Intended use
The devices which constitute this RF remote control switch set are intended only
for personal use in closed dry rooms. They are not suitable for commercial use.
The RF remote control switch set is used for switching lamps and electrical
appliances on and off. The devices may only be operated individually.
Do not plug multiple socket switches into each other. Any other use is considered
non-intended use. The manufacturer assumes no liability for damage caused
by non-intended use.
Technical data
Operating voltage
230 VAC 50 Hz
Switching voltage
230 VAC 4,35 A
Socket switch switching power
max. 1000 W
Radio signal range
max. 25 m
Operating frequency
433.92 MHz
Ambient temperature
0°C to 35°C
Storage temperature
-40°C to 70°C
CE-compliant
Adjust the DIP switches using a suitable object,
for instance a small screwdriver, by pushing them down or up.
WASTE DISPOSAL
Dispose of electrical devices in an environmentally
friendly manner!
Electrical devices do not belong in the household rubbish. In accordance
with European Directive 2002/96/EC on waste electrical and electronic equipment
old power tools must be collected separately and sent to a proper recycling facility.
You can found out more about the options for disposing of used devices from your
local government or municipal authorities.
Basic safety instructions
•
Children are not aware of the dangers that may arise from improper
handling of electrical devices. Never allow children to use electrical devices
without supervision.
•
Risk of suffocation! Do not leave the packaging material lying around.
Children could swallow the small parts and choke on them.
•
Plug the socket switches into conventional 220-240VAC/50Hz two-pin earthed
sockets only.
•
Do not connect the socket switches to extension cables.
•
Only connect consumers which do not exceed the performance limits of the
socket switches.
•
Do not connect consumers (for example irons) which could cause fi re or other
damage if they are accidentally switched on.
•
Do not connect consumers (for example refrigerators) which require condenser
motors.
•
Do not cover the socket switches. Heat builds up under the cover.
This poses a fi re hazard.
•
Regularly check the devices for damage. Do not replace damaged parts.
Contact the manufacturer or dispose of the devices in an environmentally
friendly manner.
•
Do not touch the devices with wet hands.
•
To de-energise the socket switches disconnect them from the mains supply.
Operating manual
Read this operating manual through thoroughly before using the device.
Keep the operating manual in a safe place. Should you pass on this device to
another party be sure to include the operating manual.
Synchronising the system code
Before using the devices for the fi rst time the system code must be synchronised to
enable all socket switches to react to the radio signal of the remote control.
Moreover, each socket switch must be assigned a frequency of a key pair on the
remote control to enable it to be operated individually.
Setting a system code on the socket switch
1. Undo the screw (9) of the cover (6) using a PH0 Phillips screwdriver.
2. Slightly raise the cover (6) above the screw hole (5) and push out.
3. Set the same system code as for the App using DIP switches 1 to 5 (7).
Assigning a socket switch to a control key
1. Set a control key on the remote control using DIP switches A to E (7):
Control key
DIP switch
A
B
C
D
E
A
ON
OFF
OFF
OFF
OFF
B
OFF
ON
OFF
OFF
OFF
C
OFF
OFF
ON
OFF
OFF
D
OFF
OFF
OFF
ON
OFF
2. Push the cover in (6) and close.
3. Insert the screw (9) through the screw hole (5) into the thread (8) and tighten.
Connecting the devices
The radio signal has a range of up to 25 m (dependent on structural conditions).
DIP switch E is not occupied.
The range can be affected by structural conditions (for example
reinforced concrete), electrical conditions (for example electrical lines)
or electromagnetic conditions (for example telephones). If necessary
remove the source of interference or maintain a suff cient distance
to the source of interference.
Switching on a socket switch
1. Plug the socket switch (1) into a socket.
2. Plug the consumer into the two-pin earthed socket (2).
3. Switch the socket switch (1) via app on.
The function indicator light (4) illuminates.
Switching off a socket switch
Switch the socket switch (1) via app off.
The function indicator light (4) goes out.
Reinigung
Caution! Risk of electric shock.
Before cleaning the device disconnect it from the mains supply.
Ensure that no liquid penetrates into the device. Liquid which
enters the device can cause short-circuiting.
Caution! Risk of damage from aggressive cleaning agents.
Never use aggressive or abrasive cleaning agents for cleaning.
Clean the device with a soft damp cloth and a mild cleaning agent.
Ensure that the device is completely dry before using it again.
Troubleshooting
Fault
Possible cause
Remedy
Function indicator
light (4) does not
light up.
Socket switch has not been
connected correctly.
Push the socket switch
formly into the socket.
Function indicator
light (4) lights up,
but consumer does
not work.
Consumer has not been
switched on.
Switch on the consumer.
Socket switch does
not switch on.
System code of the socket
switch has not been set
correctly.
Set the system code of
the App and on the socket
switch.
Electrical devices are
causing interference.
Remove possible sources of
interference.
Manufacturer
Hugo Brennenstuhl GmbH & Co. KG
Seestr. 1-3 · 72074 Tübingen · Deutschland
www.brennenstuhl.com
Conformity declaration
The conformity declaration can be found at the following link:
www.brennenstuhl.com/konformitaetserklaerung/ke_1507450.pdf
1 Socket switch
6 Cover
2 Childproof two-pin earthed socket
7 DIP switches
3 Two-pin earthed plug
8 Thread
4 Function indicator light
9 Screw
5 Screw hole
GB
