4-19
Initial Set-up
HYDRAULIC DRIVE INSTALLATION PRO-
CEDURE
NOTE: For a complete parts listing see
page 5-38.
NOTE: Weld-in bracket (280070) is required
if installing this hydraulic drive onto an
880 cart with S/N lower than B21300099
or a 1080 cart with S/N lower than
B21160099.
1. If installing weld-in bracket, attach
bracket to runners with a 1/4" fi llet
weld. Be sure to run weld parallel to
runners.
2. Slide universal joint over hydraulic mo-
tor shaft. Tighten 3/8"-16 setscrew.
2. Attach motor to mount plate weldment
using 1/2" hardware. See Fig. 2.
3. Attach bolt plate to hydraulic motor
side of mount plate weldment with 5/8"
hardware as shown in Fig. 2 & Fig.
3. Do not tighten at this time.
4. Install hydraulic motor on grain cart by
sliding universal joint over end of grain
cart driveshaft.
5. Attach bolt plate to runner cross mem-
ber with 1/2" hardware. Do not tighten
at this time.
6. Position motor assembly in line with
driveshaft. Securely tighten all hard-ware
previously left loose. See Fig. 3.
7. Attach tee to the hydraulic RETURN
port farthest from the tractor. See Fig.
4 and Fig. 5.
8. Install
adapter
fi tting in remaining PRES-
SURE port, followed by the 90° swivel
elbow. Attach check valve to elbow.
Verify orientation of check valve(Fig. 6).
Connect hoses, tee and quick couplers
as shown above in Fig. 6.
9. Fasten pipe elbow to tee and gauge
to pipe elbow. Position gauge in a
viewable orientation from tractor cab.
See Fig. 6.
IMPORTANT: Thread tape is recommend-
ed for all fi ttings with pipe threads.
10. Tighten all fi ttings and test for leaks.
Check auger fl ighting for correct rota-
tion.
WA R N I N G !
H I G H - P R E S S U R E
FLUIDS CAN PENETRATE THE
SKIN AND CAUSE SERIOUS INJURY OR
DEATH. SEEK MEDICAL TREATMENT
IMMEDIATELY IF INJURED BY HIGH-
PRESSURE FLUIDS. USE CARDBOARD
OR WOOD TO DETECT LEAKS IN THE
HYDRAULIC SYSTEM.
NOTE: See page 1-7 for proper procedure
on checking for hydraulic leaks.
Summary of Contents for Corner Auger 1080
