background image

9 / 16

19 Humidity indoors

20 Room climate Indicator

21 Sensor signal status

22 Sensor symbol

23 Wind/storm classification

24 Wind direction

25 Index (heat/dew point/UV/Beaufort)

26 Index value

27 Weather trend

28 AM/PM information in 12-hour time mode

7 Before starting operation

NOTICE

Avoid connectivity disruptions!

To avoid connectivity disruptions between the devices, consider the following points before starting
operation.

1. Place base station (receiver) and remote sensor (sender) together as close as possible.

2. Set up power supply for the base station and wait until the indoor temperature is displayed.

3. Set up power supply for the remote sensor.

4. Position the base station and the remote sensor within the effective transmission range.

5. Ensure that the base station and remote sensor are assigned to the same channel.

When changing batteries always change batteries in the main unit as well as all remote units and re-
place them in the correct order, so the remote connection can be re-established. If either of the
devices is mains-powered, the power supply must be disconnected for a short moment also for this
device when exchanging the batteries. If batteries are exchanged in only one of the devices (i.e. the
remote sensor) the signal can’t be received or can’t be received correctly.

Note, that the effective range is vastly affected by building materials and position of the main and re-
mote units. Due to external influences (various RC devices and other sources of interference), the
maximum distance can be greatly reduced. In such cases we suggest to position the main unit and the
remote sensor at other places. Sometimes all it takes is a relocation of one of these components of a
few inches! Though the remote unit is weather proof, it should be placed away from direct sunlight,
rain or snow.

8 Setting up power supply

Base unit

1. Remove the battery compartment cover.

2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

3. Replace the battery compartment cover.

Remote sensor

4. Loosen the screw at the battery compartment cover with a small Philips screwdriver and remove

the cover.

5. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

6. Replace the cover and retighten it with the screw.

Summary of Contents for 7002570

















Reviews: