Brevi 532, Instructions For Use Manual

12

head-sides of the carrycot (pic.1). 

1.  ABDOMINAL  BELT  TO  SECURE  THE  CHILD  IN 

THE CARRYCOT

Put the 2 ends of the belt through the holes in the bottom of the 

plastic body passing through the lining (pic. 2a).

Ensure they are correctly secured pulling the belts upwards firmly 

(pic. 2b).

2. PREPARE THE REAR SEAT-BELTS

Fasten the buckles of the

 back seat

 belts as per picture 3a.

Pull the lower-waist part of the car seatbelt (pic. 3a-1).

Take the Brevi connecting belt with the clip open (pic. 3b-D).

Make a loop in the belt and pass it through the metal ring on the 

connecting belt (pic. 3b-2).

Pass the small red metal bar into the loop (pic. 3b-3).

To fasten the buckle on the car seatbelt, pull the Brevi connecting 

belt, letting it slip to the external part of the belts (door side). To 

adjust the connecting belt, raise the loop and slide the car belt (pic. 

3c-4). To lock it in place, pull the belts again (pic. 3c-5).

Repeat the procedure with both the rear seat belts as per picture 3d.

3.  FASTEN  THE  CARRYCOT  TO  THE  SAFETY 

BELTS

Assemble the two metal pins on the carrycot shell. The pins are to 

be screwed to the front and back side of the shell (head and foot 

side). See picture 01 for Brevi’s carrycot item 739. See picture 02 

for Brevi’s carrycoot item 740. 

Fasten the carrycot to the car seat by clipping the  connecting belts 

to the external pins. 

Push the clip against the pin, forcing the red plastic lever; then pull 

it downward to lock. 

Art. 739 (Fig.4a)

Art. 740 (Fig.5a) 

Make sure to fasten at all times both the pins to the belts.

To release the carrycot, pull the red lever outwards, releasing the 

pin, and then pull the metal clip upwards.

WARNING

Make sure that the clips are correctly in place by 

pulling them up and downwards.

It must be impossible for the carrycot to move. To 

fasten the carrycot more securely,  use the seatbelt 

tightening clip system. Also make sure that the 2 

connecting belts are correctly distanced.

4. SECURE THE BABY IN THE CARRYCOT

Adjust the backrest to the horizontal position and insert the shock 

absorbers into the head side of the carrycot. The bumpers should 

be put under the lining (pic.1).

Open the waist belt by pressing the red button on the buckle.

Press the button on the left-end of the adjuster to increase the leng-

th of the belt.

Put your baby in the carrycot and fasten the belt (pic. 6-1).

Tighten the waist belt (pic. 6-2).

Always use the chest pad (part C) by threading the belt sides into 

the pad loops.

ATTENTION

Make sure the baby is secured with the safety belt 

every time you use the Brevi carrycot in the car.

Be careful not to over-tighten the belt.

Check regularly that the baby does not manage to 

open the buckle on his/her own.

Never leave the child unattended.

The backrest inside the carrycot, when used in the 

car,  has  always  to  be  in  the  horizontal  position, 

that’s to say flat. 

5. REMOVE THE BABY FROM THE CARRYCOT

Release the safety belt by pressing the red button on the buckle, 

and pull the edge out from the open loop of the pad.

NOTICE

This child restraint has been deemed “Universal” and classified ac

-

cording to Regulation No. 44, amendment series 04. It is suitable 

for general use in vehicles and is compatible with most, but not 

all, cars.

This  child  restraint  has  been  classified  “Universal”  according  to 

stricter criteria than those applied to previous models which do not 

include this notice.

In case of doubt, contact Brevi srl.

When the rear seatbelts are used for the protection of passengers, 

remove the Brevi connecting belts.

The use of parts or accessories not approved by the manufacturer 

could be dangerous.

Never leave the child unattended.

In the event of an accident, the carrycot and belts could be dama-

ged; we recommend to replace them.

Never leave the baby in the carrycot, exposed to the sun.

The carrycot body must be placed perpendicularly to the axis of the 

vehicle, as per picture (4b-5b)

The rigid or plastic parts of the fastening system should not interfere 

with the moving parts of the vehicle.

USEFUL SUGGESTIONS

 -

Retain these instructions for future reference

 -

Never use the carrycot without its lining 

 -

Never use the carrycot without its shock absorbers (side protec-

tions, part A and ventral pad, part C)

 -

The carrycot’s lining must only be replaced with one supplied by 

the manufacturer, as it is an integral part of the protection system

 -

The carrycot must be installed strictly following the present in-

structions 

 -

Regularly check that, when playing, the baby does not acciden-

tally unfasten his/her safety-belt

 -

Ensure that both the baby belt and the three-point seatbelt are 

correctly tightened to guarantee the maximum protection to your 

baby

 -

Check that the belts are not twisted

 -

Keep the belt band from being caught between the doors or rub-

bed against sharp objects. 

 -

If there are tears or frays on the belt, replace it

 -

The belts must be cleaned with a damp cloth. Do not use sol-

vents  or  bleach,  as  these  could  damage  the  belts  and  make 

them unsafe