- 24 -
b 170 v
DANGER
Keep all lubricants well away from children’s reach.
Carefully read the warnings and precautions on the lubricant
containers.
The operator should thoroughly wash himself after using lu-
bricants.
Dispose of used oil in compliance with the anti-pollution laws.
5.1.1 LUBRICATION
Lubrication of any machine with parts that turn and/or rub together
is a vitally important task for the life and functionality of the actual
machine itself. Lubrication must therefore be carried out system-
atically and at the required intervals. The frequencies given refer
to machine use in a normal environment. If this machine is used
in heavier duty conditions, it must naturally be lubricated more
frequently.
KEY to Fig. 10
1 Housing oil fill plug
2 Housing oil level
3 Oil fill plug with level
4 Oil drain with final drive
5 Grease nipple for rh rotor support
6 Grease nipple for roller adjuster screw
7 Grease nipple of roller support
5.2.1 RECOMMENDED LUBRICANTS
- For the final drive (or gearbox) and for the side transmission
gears, the Manufacturer recommends: AGIP ROTRA MP SAE
85W/140 OIL or an equivalent type complying with API-GL5/
MIL-L-2105C specifications.
- For all greasing points, the Manufacturer recommends: AGIP
GR MU EP 2 grease or an equivalent type.
When servicing the driveline, strictly comply with the instruc-
tions given by the driveline Manufacturer, in the specific opera-
tion and maintenance manual with which each driveline is
equipped.
5.2.2 AFTER THE FIRST 8 HOURS SERVICE
Each new machine must be checked after the first 8 hours ser-
vice. proceed in the following way:
- Check the general condition of the machine.
- After having checked the tines for wear, fully tighten the bolts
that fix the tines in place.
- Check to make sure that all the bolts on the machine are tight.
5.2.3 EVERY 20 HOURS SERVICE
- Check to make sure that the tine bolts are tight.
- Grease the driveline, the roller adjuster screw and the roller
supports.
5.2.4 EVERY 100 HOURS SERVICE
- Check the level of the oil in the final drive housing. Top up the
level if necessary.
- Check the level of the oil in the side housing. Top up the level if
necessary. The level is correct when oil spills from the fill plug
hole (2 Fig. 10).
5.2.5 EVERY 500 HOURS SERVICE
- Change the oil in the final drive housing after every 500 hours
service or at least once a year.
- Check to make sure that the driveline clutch is fully efficient.
Have the clutch overhauled and the plates replaced by a spe-
cialized workshop if necessary.
5.3 PREPARING FOR STORAGE
Proceed with the following operations at the end of the season or
if the machine is to remain idle for a long period of time:
- Wash all fertilizers and chemical products from the machine
and dry it.
- Carefully check the machine and replace any damaged or worn
parts.
- Fully tighten all the screws and bolts, particularly the ones that
fix the tines.
- Thoroughly grease the machine and then cover it with a tarpau-
lin and store it in a dry place.
If these operations are carried out with care, it will be all to
the user’s advantage as the machine will be in optimum con-
ditions when needed again.
If the machine must be dismantled, comply with the anti-pol-
lution laws in force. Old lubricants must and the various com-
ponents must be disposed of according to their different
structures.
5.4 SPARE PARTS
All the parts forming the machine can be ordered from the Manu-
facturer, specifying:
- The machine model.
- The serial number of the machine.
- The year of manufacture.
- The serial number of the required part (indicated in the spare
parts catalogue), a description of the part and the required quan-
tity.
- The means of transport. If this is not specified, the Manufac-
turer will dedicate diligent care to the service but shall not be
liable for delays in shipment due to causes of force majeure.
the shipping costs are always at the consignee’s charge. The
goods travel at the purchaser’s risk and peril even when sold
carriage paid.
Remember that the Manufacturer is always at your disposal
for any assistance and/or spare parts you may required.
5.4.1 SPARE PARTS TABLES ................. Page 55
Summary of Contents for b170v-250
