background image

12

 Do not use harsh abrasives, chemical cleaners or solvents to clean the exterior 

of your steam generator because they will damage the surface.

After each use

After each use, allow your steam generator to completely cool down before wiping 

the soleplate with a soft damp cloth. If polyester has burnt to the soleplate, iron a 

damp cotton cloth while your steam generator is still hot. If necessary, allow your 

steam generator to completely cool down then wipe over the soleplate with a soft cloth 

moistened with methylated spirits. Remove the methylated spirit with a damp cloth. Make 

sure that the soleplate is completely dry.
To clean the exterior of your steam generator, wipe over with a soft damp cloth and wipe 

dry. Ensure the soleplate is dry.
To remove build-up from the steam holes which may affect steam performance, use a 

cotton wool tip moistened in methylated spirits. Wipe over with a damp cloth.

Rinsing out the boiler

 NEVER remove the boiler rinse plug when your steam generator is hot. Allow 

your steam generator to cool for at least 2 hours before removing the boiler rinse 

plug.

To maintain optimum performance, it is 

important

 to rinse out the boiler in your steam 

generator once a month or after every 10 times you have used it.
Unplug your steam generator and allow it to cool for at least 2 hours. Remove the water 

tank.

1.  Remove the iron from the iron rest and place it to one side. Shake the base unit for a 

few seconds.

2.  Remove the boiler rinse plug cover by pulling it away from the base unit.
3.  Use a coin to unscrew the boiler rinse plug.
4.  Place the base unit on its side and and pour about 300ml (approx. equal to 1 coffee 

mug) of cold tap water into the opening.

5.  Shake the base unit again for a few seconds to agitate the water in the boiler.
6.  Pour out the water into a sink.
7.  Repeat steps 4, 5 and 6 again.
8. 

Refit the boiler rinse plug and tighten it firmly using a coin.

9. 

Refit the boiler rinse plug cover.

care and cleaning

Summary of Contents for vin227





















Reviews: