Auto-off Setting
• Auto-off function is set to 180 seconds by default.
• Auto-off can be set to 60 seconds, 120 seconds, 180
seconds, or disabled manually.
• To change the Auto-off time setting or disable this function:
❶ Turn off the scale.
❷ Press and hold the ON/OFF button.
❸ While holding the ON/OFF button, press the
TARE button 4-5 times quickly until “180”
is displayed.
❹ Release both buttons.
❺ Press the MODE button to switch between
“0/60/120/180”.
◦
If “0” is selected, the Auto-off function will
be disabled.
❻ After choosing the desired time, press the ON/OFF
button again.
❼ The display will show “PASS” to confirm this setting.
❽ The scale will turn off automatically.
Note:
◦
If “60”, “120”, or “180” is chosen, the scale will
turn off after the designated number of seconds of
inactivity.
◦
If the Auto-off function is disabled, the scale will
not shut off on its own.
Please note:
To maintain a longer battery life, please
turn off the scale by pressing the ON/OFF button after
each use.
Silicone Pad
Use of the silicone pad is optional. It is included to provide
additional water resistance. It also prevents slight weight
variations caused by abrupt temperature changes on the
platform.
•
Place the silicone pad onto the platform with the Brewista
logo oriented to be read left to right.
•
Ensure that the pad covers the platform completely
without interfering with platform travel.
•
The silicone pad is dishwasher safe (top rack).
Washing Instructions
This scale has been treated with a water-resistant nano-
coating. However, washing the scale under running water is
not recommended. Please follow these instructions to clean
your scale:
❶ Wash the exterior of the scale with a soft, damp cloth.
❷
Do not wash scale under running water.
❸ Leave scale to dry on a dish rack with LCD and buttons
pointing up.
DO NOT use liquid bleach or other harsh chemicals.
DO NOT use steel wool or abrasive sponges as this can
scratch the surface.
DO NOT submerge the scale.
Avoid pouring water directly into your scale, as water
may become trapped. If this occurs drying time may
exceed 4 hours.
Water drops on the LCD display will not interfere with
your weighing. These drops will dry and disappear.
If the scale displays
“UNST”
or the readings jump after
washing, then water is still inside the scale. Simply shake
out the excess water and let your scale dry longer.
By following these washing instructions, you will experience
shorter drying times and your scale will provide you with years
of reliable service.
Mode 6:
(for Pour Over Brewing)
❶ Place brew vessel on the scale platform.
◦
Weight reading goes to 0.0g (Auto-tares).
❷ Add coffee grounds to the brewing vessel.
❸ Adjust the amount of coffee grounds to the desired
weight.
❹ Once platform is stable, press the TARE button.
❺ Start adding water to the coffee grounds.
◦
Count-up timer starts.
❻ Remove cup after brewing.
◦
Weight reading remains on the display for five
(5) seconds after removing the cup.
◦
After a five (5) second delay, time returns to
0’00” and weight returns to 0.0g.
Tare Function
• Tare function is disabled under “AUTO” mode.
• Under Manual modes: press the TARE button when
needed.
❹ Remove cup after brewing.
◦
Weight reading remains on the display for five
(5) seconds after removing the cup.
◦
After a five (5) second delay, weight returns to
0.0g.
Mode 5:
(Auto-tare and Auto-timer with timer starting when liquid hits
the cup for espresso preparation.)
❶
Place cup on the scale.
◦
Weight reading goes to 0.0g (Auto-tares).
❷ Push button on espresso machine to start the shot.
◦
When liquid hits the cup the timer automatically
starts to count up. To pause the timer, press
TIME button.
❸ Remove cup after brewing.
◦
Weight reading remains on the display for five
(5) seconds after removing the cup.
◦
After a five (5) second delay, time returns to
0’00” and weight returns to 0.0g.
Calibration
❶ While the scale is off, press and hold ON/OFF button and
MODE button at the same time until LCD shows internal
code, then release the two buttons.
❷ Press the MODE button again.
◦
The LCD will read “0.0g”.
❸ Place a 500g weight onto the center of the platform
◦
The LCD will show internal code.
❹ Press MODE button again.
❺
The LCD will read “PASS”.
❻ Calibration is complete.
Warning Messages
•
“EEEE”: Overload
◦
Quickly remove weight from platform to protect
the scale.
•
“UNST”:
◦
Scale is not steady during start up. Please turn off
scale, set on a stable surface and restart scale.
◦
Water is inside the scale. Shake out excess water
and let dry.
