background image

 

Copyright © Bridgetek Pte Ltd                

 

 

 

 

    

           1

 

 

LDSBus Multi Sensor Datasheet  

Version 1.0 

 

Document Reference No.: BRT_000360    Clearance No.: BRT#181 

 

1

 

Introduction 

 

The LDSBus Multi Sensor consists of 4 sensors 
in a compact low-profile design. Temperature, 
humidity, Passive Infra-Red (PIR) based 
motion detection and ambient light 
measurement sensors are incorporated in this 
multi-sensor device. Available in 4in1 and 3in1 
(without motion detector) combinations, the 
device can be flush mounted on ceilings or 
swivel mounted on walls. The multi-sensor 
works with the Bridgetek PanL Smart Living, 
IoTPortal and LDSBus Python SDK products.  

1.1

 

Features 

 

 

3in1 and 4in1 combination options  

 

 

3 levels of motion sensitivity with 
customizable motion re-trigger interval and 
wide angle of motion detection  
 

 

Measures temperature up to 70

o

C with 

accuracy of ±0.2°C  

 

 

Measures humidity from 0 to 95% with 
accuracy of ±2%RH 

 

 

Measures ambient light up to 64K Lux  

 

 

Implements the Bridgetek LDSBus protocol. 

 

 

Low power consumption  5V, 180mW  

 

 

Operating temperature range : 0

o

C to +70

o

 

 

Swivel mount and Flush mount options  

 

 

Supported platform application:  
Bridgetek PanL Smart Living, IoTPortal and 
LDSBus Python SDK  
(Visit 

http://bit.ly/ldsbus-resources

) 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced 
in  any  material  or  electronic  form  without  the  prior  written  consent  of  the  copyright  holder.  This  product  and  its  documentation  are 
supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Bridgetek Pte Ltd 
will  not  accept  any  claim  for  damages  howsoever  arising  as  a  result  of  use  or  failure  of  this  product.  Your  statutory  rights  are  not 
affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the 

product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject 
to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of th is document. 
Bridgetek Pte Ltd, 178 Paya Lebar Road, #07-03, Singapore 409030. Singapore Registered Company Number: 201542387H 
 

LDSBus Multi Sensor 

Datasheet  

 

Summary of Contents for LDSBus



















Reviews: