background image

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol  

 is used to identify safety infor-

mation about hazards that can result in personal injury.  A 

signal word

 (DANGER, WARNING, or CAUTION)

 is used 

with the alert symbol to indicate the likelihood and potential 

severity of injury.  In addition, a hazard symbol may be used 

to represent the type of hazard.

 DANGER 

indicates a hazard which, if not avoided, 

will result in death or serious injury

.

 

WARNING 

indicates a hazard which, if not    

 

avoided, 

could result in death or serious injury

.

 

CAUTION 

indicates a hazard which, if not  avoided,   

could result in minor or moderate injury

.

NOTICE

 indicates an action that could result in damage to 

the product.

Hazard Symbols and Meanings

Symbol

Meaning

Safety information about the hazards 

that can result in personal injury.

Read the directions for use of the 

product before operating.

Keep hands and feet away from deck.

Thrown object hazard.

Roll over hazard.

Manual Contents:

Operator Safety ............................................................2
Hardware and Parts Identification...............................4
Assembly ......................................................................5
Operation......................................................................10
Storage.........................................................................10
Warranty.......................................................................11

General Information

The illustrations in this document are representative. 

Your unit may vary from the images displayed. 

LEFT

 and 

RIGHT

 are referenced from the operator’s position.

All packaging, used oil, and batteries 

should be recycled according to 

applicable government regulations.

All language translations of this document are derived 

from the original English source file.

2

Not for Reproduction

Summary of Contents for 1696462-00













Reviews: