background image

4

briggsandstratton.com

 WARNING 

Thrown Objects Hazard

Do not open the cover while the blades are turning.

• Check the catcher system to make sure it is bolted

tightly to the unit.

• Catcher bags are subject to deterioration and wear

during normal use. Inspect the bag periodically for

tears, holes, or weak spots and replace with a new bag

that meets manufacturer’s durability standards.

 WARNING 

Loss of Control, Roll-over and Tipping Hazard

• Use reduced speed on uneven ground and when

turning corners.

• Reduce loads on hillsides. It is recommended that the

catcher system be kept only half full when mowing any

slope. Start mowing on slopes when the catcher system

is empty.

• Mow on the face of slopes as directed in the operator’s

manual and safety warnings on the product.

• Never operate on slopes greater than 17.6% (10°).
• Select a slow ground speed before driving onto a slope.

Avoid using brakes to control speed.

• Use caution when changing directions and DO NOT

start or stop the rider while on a slope.

Safety Decals - Triple C

atche

r

Before operating the grass catcher, read and understand the

 

installed safety decals. The decals are provided to help you

 

avoid personal injury or damage to the product. 
If any safety decals become damaged or illegible, order

 

replacements from your local authorized dealer. See Figure 1.

1

Callout Hazard

Description

1

Thrown Object Hazard

Do not open the 

catche

r while the mower blades are

 

turning.
Do not operate the mower without the complete grass

 

c

atche

r in place. Keep bystanders and children a safe

 

distance.

Callout

Hazard

Part Number

A

Thrown Objects Hazard

7104709

Hardware and Parts - Grass

Catcher

See Figure 2.

CALL

OUT

DESCRIPTION

SPECIFICATION

QTY.

A

SIDE PLATE

-

2

B

CAPSCREW

.375”-16 x 1.00”

4

C

LOCK NUT, Flange

.375”-16

4

D

CAPSCREW

.50”-13 x 2.50”

4

E

WASHER

.531” ID x 1.25” OD x .08” THK

4

F

SPACER

.52” ID x .73" OD x 1.27"

4

G

NUT, Nylock

.50”-13

4

H

CARRIAGE BOLT

.375”-16 x 1.0"

4

I

FLANGE NUT,

Whiz-Lock

.375”-18

4

J

COVER HINGE PIN

-

2

K

HAIR PIN

-

2

L

CROSS SUPPORT

-

1

M

COVER ASSEMBLY

-

1

N

CATCHER BAG

-

3

O

UPRIGHT SUPPORT

ASSEMBLY

-

1

Refer to the chart for the callouts, descriptions, specifications

and quantities.

Not for 

Reproduction

Summary of Contents for 1697363A-00













Reviews: