background image

Not for 

Reproduction

20

ferrismowers.com

45

5. Engage the parking brake. The neutral lockout bolts will

enter the notches of the neutral lockout plates (C).

6. Position the neutral lockout bolts to the center of the

notches of the neutral lockout plates.

7. Re-tighten the jam nuts.

Purging the Air from the Hydraulic

System

Due to the effects air has on efficiency in hydraulic drive

systems, it is critical that it be purged from the system.

These purge procedures should be implemented any time a

hydraulic system has been opened to facilitate maintenance

or any additional oil has been added to the system.
The resulting symptoms of air in the hydraulic system may be:

• Noisy operation.
• Lack of power or drive after short term operation.
• High operation temperature and excessive expansion of

oil.

Before starting, make sure the transaxles/transmissions are

at the proper oil levels. If it is not, fill to the specifications

outlined in the 

Check / Fill Transmission Oil Level

 procedure.

Purging Air from the Hydraulic System:

1. Chock the front wheels to prevent the machine from

rolling. Raise the rear of the machine so that the vehicle’s

rear tires do not contact the ground. Position jack stands

under the rear bumper of the machine to secure it.

2. Open the transaxle’s bypass valves (see 

Uncrating

 for

the location and function of the bypass valves), start

the engine, release the parking brake, and slowly move

the zero-turn rider’s ground speed control levers in both

forward and reverse directions (5 to 6 times), as air is

purged from the unit, the oil level will drop.

3. Stop the engine and engage the parking brake.
4. Close the transaxle’s bypass valves, start the engine,

release the parking brake, and slowly move the zero-turn

rider’s ground speed control levers in both forward and

reverse directions (5 to 6 times), as air is purged from the

unit, the oil level will drop.

5. Stop the engine. Remove the jack stands from

underneath the machine.

6. Repeat the process detailed above but with the unit's

drive wheels on the ground. The procedure should be

performed in an area free of any objects or bystanders.

It may be necessary to repeat the process detailed above

until all the air is completely purged from the system. When

the transaxles/transmissions operate at normal noise levels

and move smoothly forward and reverse at normal speeds,

then the transaxles/transmissions are considered purged.

Suspension Adjustment

The shock assemblies (A, Figure 46) can be adjusted in two

ways to allow the operator to customize the ride according to

the operator's weight and/or operating conditions. You have

the option of adjusting the spring pre-load and/or the upper

mounting position. 

46

 

Items to consider before adjusting the suspension:

 

Summary of Contents for IS3200Z Series

























Reviews: