background image

15

Warranty

BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment 

that is defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of 

charge, any part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both. 

Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. 

This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the 

nearest Authorized Service Dealer using our dealer locator at www.BriggsandStratton.com.
There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular 

purpose, are limited to one year from purchase or to the extent permitted by law. Liability for incidental or consequential 

damages are excluded to the extent exclusion is permitted by law. 
Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries 

do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion 

may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from 

state to state or country to country.

WARRANTY PERIOD

ABOUT YOUR WARRANTY

Item 

        Consumer Use 

     Commercial Use: 

Equipment 

1 Years                                         N/A

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues 

for the period of time stated above. “Consumer use” means personal residential household use by a retail consumer. 

“Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once product 

has experienced commercial use, it shall thereafter be considered as commercial use for purposes of this warranty.
No warranty registration is necessary to obtain warranty on Briggs & Stratton products. Save your proof of purchase receipt. 

If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of 

the product will be used to determine warranty eligibility.

We welcome warranty repair and apologize to you for being inconvenienced. Warranty service is available only through 

servicing dealers authorized by Briggs & Stratton or BSPPG, LLC. 
Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This 

warranty only covers defects in materials or workmanship. It does not cover damage caused by improper use or abuse, 

improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse 

- The proper, intended use of this product is described in the Operator’s Manual. Using the 

product in a way not described in the Operator’s Manual or using the product after it has been damaged will void your 

warranty. Warranty is not allowed if the serial number on the product has been removed or the product has been altered or 

modified in any way, or if the product has evidence of abuse such as impact damage, or water/chemical corrosion damage.

Improper Maintenance or Repair

 - This product must be maintained according to the procedures and schedules 

provided in the Operator’s Manual, and serviced or repaired using genuine Briggs & Stratton parts. Damage caused by lack 

of maintenance or use of non-original parts is not covered by warranty.

Normal Wear 

- Like all mechanical devices, your unit is subject to wear even when properly maintained. This warranty 

does not cover repairs when normal use has exhausted the life of a part or the equipment. Maintenance and wear items 

such as filters, belts, cutting blades, and brake pads (engine brake pads are covered) are not covered by warranty due to 

wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale Fuel

 - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the 

Operator’s Manual. Damage caused by stale fuel (carburetor leaks, clogged fuel tubes, sticking valves, etc) is not covered 

by warranty.

* Applies to Briggs and Stratton engines only. Warranty coverage of non-Briggs and Stratton engines is provided by the engine manufacturer.

No

t fo

r  

Rep

rod

uct

ion

Summary of Contents for ZT

















Reviews: