background image

13

DISCLAIMERS

Brightline

 guarantees all its products to be free from defects in materials and

workmanship for a period of one (1) year from the date of shipment.

If any product is found to be unsatisfactory under this warranty, the buyer must notify

Brightline

 immediately.  Once a course of action has been determined, if it is neces-

sary to return the product to 

Brightline

 a Return Authorization (RA) will be issued.

Ship the product directly to 

Brightline

, 580 Mayer Street, Building #7, Bridgeville, PA

15017. The RA number should be marked on the shipping carton. The unit will be

replaced or put into proper operating condition, free of all charges. The correction of

any defects through repair or replacement by 

Brightline

 shall constitute fulfillment of

all obligations and liability of 

Brightline

 to the buyer under this warranty and the

contract of sale.

Brightline

 is not responsible for damage to its products caused by improper

installation, maintenance, or use; by improper electrical hookups; or by unauthorized

repairs.

Failure to notify 

Brightline

 of unsatisfactory operation or any improper or

unauthorized installation, maintenance, use, repairs, or adjustments shall terminate the

warranty and 

Brightline

 shall have no further responsibility under the warranty.

Brightline

 shall not be liable for special or consequential damages in any claim,

action, suit, or proceeding arising under this warranty or contract of sale, nor shall

Brightline

 be liable for claims for labor, loss of profits or goodwill, repairs, or other

expenses incidental to replacement.

Brightline

 makes no other warranty of any kind

whatsoever, expressed or implied, and all implied warranties of merchantability and

fitness for a particular purpose that exceed the obligation specifically described in this

warranty are hereby disclaimed by 

Brightline

 and excluded from this agreement.

All shipments, unless otherwise noted, are F.O.B. factory.

The customer is advised to inspect for shipping damage, apparent and/or hidden.

If detected, notify the transportation company and file your claim.

WARRANTY

PROCEDURES

580 Mayer Street, Building #7,  Bridgeville, PA  15017 

  phone  412.206.0106 

  fax  412.206.0146

www.brightlines.com

Summary of Contents for Stealth-T















Reviews: