INSTALLATION AND OPERATION MANUAL
ORVIS – LED floodlight
EN
floodlight
www.brilum24.pl
www.brilum24.pl
ORVIS
ORVIS, 10W
ORVIS, 20W
ORVIS, 30W
ORVIS, 50W
ORVIS, 70W
ORVIS, 100W
ORVIS, 150W
ORVIS, 200W
IP 65
CRI>80
185
-
240VAC
50Hz
HIGH QUALITY
BRILUM S.A.
ul. Wilanowska 1A, 05-520 Konstancin-Jeziorna, Poland
ORVIS
CHARACTERISTICS
ORVIS – energy-saving LED floodlights made of aluminum die cast. The surface has
been treated with an electrostatic coating and is characterized by strong adhesion, water
resistance, dust resistance and a rational construction. Protection rating – IP 65.
Thanks to high quality of materials and components, floodlight ORVIS is safety, reliable,
energy saving and has long lifespan.
LED LIGHT SOURCES
ORVIS floodlights have been equipped with revolutionary and technologically advanced
COB (Chip on board). Light colour: neutral white.
APPLICATION
ORVIS floodlights can be applied for lighting of various objects: building elevations,
courtyards, entrances, gates, garden plants, external walls of buildings or other architectural
landmarks.
TECHNICAL DATA
Optical system
reflector made of aluminum
Light viewing angle
120°
Voltage
185 ÷ 240V AC
Frequency
50/60Hz
Power of luminaire
10W
20W
30W
50W
70W 100W 150W 200W
Protection rate
IP 65
Protection against electric shock
I
Type of LEDs
COB (Chip on board)
Correlated colour
temperature (CCT)
4000K
Colour rendering index (CRI)
>80
LED lifetime*
~ 30 000 hours
Luminous flux (lm)
850 lm 1700 lm 2550 lm 4250 lm 5950 lm 8500 lm 12750 lm 17000 lm
Mounting height
to 5m
to 10m
to 15m
Operating temperature
-30°C ÷ +50°C
Weight
0,60kg 0,90kg 1,10kg 1,40kg 2,30kg 2,50kg 4,00kg 4,00kg
* this parameter is detailed on the basis of data provided by a LED manufacturer
INSTALLATION
WARNINGS!
➢ This appliance is only suitable for fixed mounting.
➢ During the installation and maintenance of the luminaire turn off the power supply!
➢ Supply cables must be connected according to the instruction and national regulations.
➢ Luminaires are recommended to be installed by a qualified electrician.
➢ Replace cracked protection glass.
➢ If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the similar qualified person in order to avoid a hazard.
MOUNTING:
The bow handle allows to mount the luminaire on the ground and to change the angle
of depression.
Ø
Ø
10
100
13
35
Ø
Ø
8
95
8
20
Ø
Ø
6
60
8
12
ORVIS, 10W
Ø
Ø
10
102
13
35
Ø
Ø
10
152
13
40
Ø
Ø
10
140
13
40
100W
Ø
Ø
10
140
13
40
Ø
Ø
10
152
13
40
ORVIS, 70W
ORVIS, 100W
ORVIS, 150W
ORVIS, 200W
1. Mark points for drilling mounting holes.
2. Drill properly spaced mounting holes at the mounting place.
3. Fasten the LED floodlight on the surface.
4. Connect the power cable to the proper connector terminals:
L - brown
N - blue
- yellow
5. Stabilize the luminaire position.
yellow -
blue - N
brown - L
SAFETY AND MAINTENANCE
➢ The installation of the luminaire should be done by the certified and experienced
electrician.
Before starting the installation you must absolutely turn off the power supply
at the mains where the luminaire has to be connected for protection from accidental current
supply!
➢ Sometimes luminaire must be served for keeping the optimal technical parameters. Before
you clean the product, disconnect it from power supply and let it cool down. Insubmission
can lead to electric shock or to the sting while cleaning the product. Housing of the
luminaire should be cleaned by generally available washing measures and also rubbed
dry with a soft cloth. Don’t use corrosive agents and solvents. Don’t use stream of water
under the pressure.
The information included in this document may undergo changes without warning.
Possible changes will be taken into consideration while working with other issues of the
instructions for use or complementary documents. The Manufacturer does not bear any
responsibility for any possible damage caused to the Consumer in case of the Manufacturer’s
requirements specified in the given instruction manual have been disregarded. According
to article 568 pt 1 of the Polish Civil Code, the right resulting from a warranty for physical defects
are extinct after the lapse of 2 (two) years after delivery of the luminaire to the Consumer.
This symbol stands for selective collecting of the electrical and electronic
equipment, therefore, this product cannot be treated as other household’s waste.
It has to be left at a special used-equipment collection point. The appropriate dealing
with the collection of used electrical and electronic equipment is crucial, especially
if the equipment includes dangerous components which have a negative influence on the
environment and on the health of people.
ORVIS, 20W
ORVIS, 30W
ORVIS, 50W
120
°
