BRITAX RÖMER Kindersicherheit GmbH
Blaubeurer Strasse 71
D-89077 Ulm
Germany
T.: +49 (0) 731 9345-199/-299
F.: +49 (0) 731 9345-210
E.: service.de@britax.com
www.britax.eu
BRITAX EXCELSIOR LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
T.: +44 (0) 1264 333343
F.: +44 (0) 1264 334146
E.: service.uk@britax.com
www.britax.eu
Please take the time to read these instructions carefully and keep them
to hand in the intended storage compartment
05
on the child safety seat at
all times! The instructions must be kept with the child safety seat if the latter
is passed on to a third party.
3. SAFETY NOTES
DANGER! For the protection of your child:
In the event of an accident at a collision speed of more than 10 km/h, the child
safety seat may be damaged without the damage becoming immediately visible. In
this case, the child safety seat must be replaced. Please dispose of it properly.
• Always have your child safety seat checked if you suspect it may have been
damaged (e.g if it falls on the ground).
• Regularly check all important parts for damage. Ensure that all mechanical parts,
in particular, are fully functional.
• Never lubricate or oil parts of the child seat.
• Never leave your child unattended in the child seat in the vehicle.
• Only allow your child to enter and exit the vehicle on the pavement side.
• Protect the child safety seat from intensive direct sunlight when it is not in use.
The child safety seat can get very hot in direct sunshine. Children's skin is sensi-
tive and could be harmed as a result.
• The more snugly the belt fits over your child's body, the better they will be protected.
Avoid putting thick clothes on your child under the belt.
• Take regular breaks on long journeys in order to give your child the opportunity to
run about and play.
• Use on the rear seat: Move the front seat far enough forwards to ensure that your
child's feet cannot hit the backrest of the front seat (to prevent risk of injury).
• If your child tries to open the red ISOFIT safety button 06 or a buckle, stop the
vehicle as soon as it is safe to do so. Check whether the child safety seat is correctly
fastened and ensure that your child is correctly secured. Explain to your child the
dangers associated with their actions.
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or objects may
cause injury to other vehicle occupants. Please always check that:
• the backrests of the vehicle seats are locked, e.g. that a foldable rear seat bench
latch is engaged.
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
secured.
• all persons in the vehicle have their seat belts fastened.
• the child safety seat is always secured when it is in the vehicle, even if no child is
being transported.
WARNING! For your protection when handling the child seat:
• Never use the child safety seat free standing, not even for test sitting.
• To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
• Keep the child safety seat in a safe place when it is not in use. Do not place any
heavy objects on the seat and do not store it directly next to sources of heat or in
direct sunlight.
4. USE IN THE VEHICLE
Please observe the instructions for using children's restraining systems in the operating
instructions of your vehicle.
The seat can be used in vehicles with
ISOFIX anchoring systems
(see type list)
and in vehicles with a
3-point belt.
To determine which seats are approved for use with
child safety seats that meet the
requirements for weight classes 9 to 18 kg
and
15 to 36 kg
, please refer to the
operating
instructions of your vehicle
.
9-36 kg
The
EVOLVA 1-2-3 SL SICT
is approved for two different methods of installation:
Group
Installation method
Means by which child
is secured
Section of
user instructions
1 (9-18 kg)
Vehicle belt
With 5-point harness
A
1 (9-18 kg)
Vehicle belt + soft latch
With 5-point harness
A
2+3 (15-36 kg)
Vehicle belt
Vehicle belt
B
2+3 (15-36 kg)
Vehicle belt + soft latch
Vehicle belt
B
a)
This means that the child safety seat may only be used in vehicles that are listed in the enclosed
vehicle type list. This type list is consistently kept up to date.
The latest version can be obtained from us or from www.britax.com
You can use your child safety seat as follows:
In the direction of travel
Yes
Against the direction of travel
No
1)
With 2-point harness
No
With 3-point belt
2)
Yes
with ISOFIX fastening points (be-
tween seat surface and backrest)
Yes
On front passenger seat
Yes
3)
On outer rear seat
Yes
On centre rear seat
(with 3-point belt)
Yes
4)
1) Use on a rearward-facing vehicle seat (e.g. in a van or minibus) is only permitted if the vehicle
seat is also approved for use by adults. The seat may not be in the area of effect of an airbag.
2) The safety belt must be approved to ECE R 16 or a comparable standard, e.g. see whether
there is an "E" or "e" in a circle on the belt test label.
3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions
in the vehicle owner's manual.
4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.
PAGE I
7. HARNESS BUCKLE CARE
1. PRODUCT OVERVIEW
DISPOSAL:
Please observe the waste disposal regulations in your country.
Disposal of packaging
Container for cardboard boxes
Seat cover
Residual waste, waste incineration
Plastic parts
To be placed in the corresponding
container according to labelling
Metal parts
Container for metals
Belt straps
Container for polyester
Buckle and tongue
Residual waste
6. CARE AND MAINTENANCE
Please ensure that you only use original BRITAX RÖMER replacement
covers, as the seat cover is an integral part of the child safety seat and fulfils
important functions to ensure the smooth operation of the system. Replace-
ment covers are available from your dealer.
•
The cover can be removed and washed in accordance with the instruc-
tions on the wash care label.
•
The plastic parts can be cleaned using soapy water. Do not use any caus-
tic cleaning agents (such as solvents).
DANGER!
The child seat must not be used without the seat cover.
CAUTION!
Never remove the buckle tongues
30
from the straps.
9 to 36 kg
(~9 months to
12 years of age)
www.britax.com
2000025513 16/08
GB
EVOLVA
1-2-3 SL SICT
User instructions
5. CHANGING THE HARNESS
Removing the 5-point harness
1.
Loosen the harness straps as far as possible (see 9.1).
2.
Push the shoulder strap adjuster
24
all the way up
(see 8.1).
3.
Unhook the shoulder straps
13
from the connecting
piece
14
.
4.
Clip the connecting piece
14
at the bottom of the
backrest
04
into its holder
11
.
5.
Push down the strap loops of the shoulder pads
18
from the base of the shoulder strap adjuster
24
.
6.
Pull the shoulder straps
13
and the strap loops of the
shoulder pads
18
out of the belt slots.
7.
Undo the Velcro fastener on the crotch cushion
21
and
remove it.
8.
On the bottom of the seat, unhook the adjusting strap
23
from the metal plate
27
.
9.
Turn the metal plate
27
(that holds the harness buckle
19
to the seat shell) on end and push it upwards
through the belt slot
28
.
10.
Release the harness buckle
19
.
11.
Push the straps and buckle tongues
30
through the lap
belt slots in the cover.
12.
Place the harness buckle
19
under the cover and inside
the storage compartment
31
of the backrest
04
.
13.
Push the adjusting strap
23
under the cover.
14.
Fix the shoulder pads
18
and shoulder straps
13
in the
rubber loops
32
at the feed-through points
15
.
Installing the 5-point harness
►
To install the straps, follow the steps in reverse order.
DANGER!
Tug on the shoulder straps firmly
13
to make
sure that the 5-point harness is secure.
Removing the cover
1.
Adjust the headrest by moving it up
16
(see 9.1).
2.
Unhook the edge of the cover and the rubber loops on
the back of the headrest
16
.
3.
Pull off the cover of the headrest
16
.
4.
Unhook the rubber loops from the retaining screws on
the backrest
04
.
5.
Loosen the shoulder straps
13
(see 9.2).
6.
Undo the Velcro fastener on the crotch cushion
21
and
remove it.
7.
Open the snaps
on the left and right-hand sides of the
backrest cover
04
.
8.
Unthread the harness buckle
19
and the adjusting strap
23
from the cover.
9.
On the bottom of the seat, unhook the rubber loop of
the cover from the retaining screws and cover flaps
24
.
10.
Working from the side, carefully pull the edge of the
cover on the backrest
04
over the SICT
08
.
11.
Slide the cover with opening over the headrest
16
.
►
The cover can now be washed in accordance with the
instructions on the wash care label.
Re-fitting the cover
►
Proceed in reverse order to re-fit the cover.
WARNING!
Ensure that the straps are not twisted and
that they have been correctly inserted in the belt slots on
the cover.
To ensure the safety of your child, it is absolutely essential that the harness
buckle continues to function correctly. Harness buckle malfunctions are usually
caused by a build-up of soiling or by external objects.
Possible faults:
• When you press the red release button, it takes a long time for the buckle
tongues to be ejected.
• The buckle tongues no longer engage (i.e. when you try to push them in, they
pop out again).
• The buckle tongues engage without an audible "click".
• The buckle tongues are difficult to push in (you feel a certain amount of
resistance).
►
Remedy:
Clean the harness buckle so that it functions properly again:
Cleaning the harness buckle
1.
Remove the harness buckle
19
(see 5.1).
2.
Soak the buckle
19
in warm water containing washing-up
liquid for at least an hour.
3.
Rinse the buckle
19
thoroughly and dry it.
4.
Turn the metal plate
27
on end and push it downwards
through the belt slot
28
in the cover
and through the
seat shell.
5.
Turn the metal plate
27
90° and hook the adjusting strap
23
into the metal plate
27
(5.8).
DANGER!
Tug hard on the harness buckle
19
to make
sure that it is secure.
6.
Push the crotch cushion
21
into the belt slot and use the
Velcro fastener to fix it to the harness buckle.
01
02
03
01
ISOFIX fastening points (car)
06
ISOFIT Locking button
02
ISOFIX insertion aids
07
ISOFIT locking arms
03
Headrest adjuster
08
SICT
04
Backrest
09
Cover flap
05
Compartment for the user instructions
10
ISOFIT adjustment button
09
06
04
07
If you have any questions regarding the use of the product, please feel free to contact us:
2. APPROVAL
BRITAX RÖMER
Vehicle child
safety seat
Tested and approved according to ECE* R 44/04
*ECE = European Standard for Child Safety Equipment
Group
Body weight
EVOLVA 1-2-3 SL
SICT
I
9 to 18 kg
II+III
15 to 36 kg
The child safety seat has been designed, tested and approved according
to the requirements of the European Standard for Child Safety Equipment
(ECE R 44/04). The seal of approval E (in a circle) and the approval number are
located on the orange approval label (sticker on the child safety seat).
DANGER!
This approval will be invalidated if you make any modifications to
the child safety seat. Only the manufacturer is permitted to make modifica-
tions to the child safety seat.
WARNING!
Use the EVOLVA 1-2-3 SL SICT exclusively for securing your
child in your vehicle. It is in no way suitable for use as a seat or toy in the
home.
DANGER!
Never secure your child or the child safety seat with a 2-point
belt. If you secure your child in the child seat with only a 2-point belt, this
may cause serious injuries to your child in the event of an accident and could
even result in their death.
DANGER!
Never use installation method A for the child safety seat unless
the harness buckle and shoulder pads are properly attached (the straight
edges of the shoulder pads must be pointing towards each other). Make
sure that the metal plate of the harness buckle is correctly attached.
WARNING!
Ensure that the straps are not twisted, that they have not been
accidentally interchanged and that they have been correctly inserted in the
belt slots on the cover.
05
08
10
19
19
27
28
11
14
04
24
18
23
27
27
19
28
31
19
04
21
18
13
32
15
32
13
14
16
21
04
04
23
24
24
04
08
16
28
160908_EVOLVA_123_SICT_DRAFT_GB_GRAFIKEN.indd 1
9/7/2016 9:04:53 PM